The major factors affecting the removal efficiency of sulfamethazine (SMT) by photocatalysis process in the presence of TiO2 P25 or ZnO, namely the pH, the amount of catalyst and the initial SMT concentration were examined. The obtained results showed the absence of adsorption of SMT on the catalysts and the absence of degradation of SMT by direct photolysis under UV light in the absence of catalyst. The variation of the pH solution in the range 4–9 did not cause any significant degradation of SMT. The optimal amounts of each catalyst were, respectively, 0.5 and 0.25 g/L for TiO2 P25 and ZnO. Increasing the initial SMT concentration impacted negatively the removal efficiency, which decreased from 31% to 13% and from 100% to 27% in the presence of TiO2 P25 and ZnO in the presence of 10 mg/L and 50 of SMT after 30-min reaction time, respectively. The obtained results showed better efficiency of ZnO than TiO2 P25 regarding both removal efficiency and chemical oxygen demand (COD) abatement. However, removal efficiency and COD abatement were not complete, even after 7 h of photocatalysis, about 92% and 41%, respectively. The biodegradability was examined after photocatalysis performed in the following conditions: [SMT]0 = 50 mg/L, pH = 6, T = 25°C, ω = 360 rpm and 0.5 g/L of TiO2 P25 or 0.25 g/L of ZnO. In these conditions, the removal efficiencies were, respectively, 26% and 41% in the presence of TiO2 P25 and 55 and 92% in the presence of ZnO after 4 and 7 h of pretreatment times, respectively. The BOD5/COD ratio increased substantially and, respectively, from 0 to 0.25 and from 0 to 0.16 in the presence of TiO2 P25 and ZnO after 7 h of irradiation. Even if the limit of biodegradability (0.4) was not achieved, a subsequent biological treatment was considered in the presence of TiO2 P25, leading to 58% COD abatement after a 28-day culture.
12 December 2018 in Separation Science and Technology
In this paper, the modeling and the optimization of the removal efficiency of ketoprofen (KTP) by the electrocoagulation process were studied. The central composite design experiments (CCD) method was used to study the main effects and the interaction effects between operational parameters and to optimize the value of each parameter. According to the regression equation obtained, the current density appears to be one of the most important parameters (b2 = +22.11) controlling the removal efficiency of KTP. The positive sign of b2 coefficient suggests that the increase of current density increases the yield of removal. The second significant parameter with a negative effect was the initial KTP concentration (b3 = −16.27). This result suggests that the removal efficiency was inversely proportional to the initial concentration. In addition, according to the model, the most influencing interactions were pH-current density, pH-initial concentration, and current density-initial concentration. The model obtained by CCD led to the following optimal conditions for KTP removal efficiency (96.70%): pH = 7, i = 24.04 mA cm−2, and C0 = 5 mg L−1.
The feasibility of combining an electrochemical treatment on a carbon felt electrode and a biological treatment for the degradation of tetracycline (TC) and tylosin (Tylo) is presented. Central composite design (CCD) was employed to optimize the effects of the operating parameters on the electrochemical treatment efficiency. The variables investigated were the electrolysis time, the applied current intensity and the initial TC and Tylo concentrations. The second-order model obtained by CCD led to the following optimal conditions for the abatement of the chemical oxygen demand (COD): 241.66 mA ≤ I ≤ 250 mA, [TC]0 = 50 mg L−1 and 120.0 min ≤ telecrolysis ≤ 132.9 min for TC and 50 mA ≤ I ≤ 80 mA, 10 mg L−1≤ [Tylo]0 ≤ 13 mg L−1 and telecrolysis = 240 min for Tylo. Under these conditions, the obtained yields of COD abatement were 80% and 69% for TC and Tylo, respectively. To assess the effectiveness of electrolysis as a pretreatment before a biological process, biodegradability tests were conducted on a solution electrolyzed at 250 mA, 50 mg L−1 initial TC or Tylo and during 240.0 and 180.35 min for TC and Tylo, and showed an improvement of the BOD5/COD ratio, from 0.033 to 0.46 and from 0.04 to 0.33 for TC and Tylo, respectively. From this, the electrochemical pretreatment of TC and Tylo generated intermediate products, which are at least partially biodegradable. The combination of an electrochemical pretreatment in the same conditions with a biological treatment involving activated sludge confirmed these positive results, since it showed an overall dissolved organic carbon (DOC) removal close to 92% and 89% for TC and Tylo, respectively.
In this study, the degradation of paracetamol (PCT) by thermo-activated peroxydisulfate (PDS) and the feasibility of coupling thermo-activated peroxydisulfate to activated sludge culture were examined. The effect of the relevant parameters on the thermo activated peroxydisulfate process, namely temperature, PDS concentration, initial pH and initial PCT concentration was investigated. As observed, the solution pH did not have a significant effect on the PCT degradation. The temperature increased the degradation of PCT, while an increase of the initial PCT concentration impacted negatively its degradation yield. The PDS concentration showed an optimal value of 8 mM. The operating parameters were then optimized by using a central composite design (CCD). After performing a screening of the various factors, response surface analysis led to the following optimal conditions for the yield of PCT degradation: 0.33, 5 mM, pH = 6 and 68°C for the initial PCT concentration, the initial peroxydisulfate concentration and the temperature respectively, leading to the removal of 94.2% of PCT. Under these conditions, the BOD5/COD ratio increased from 0.008 initially to 0.34 after 10 h. Showing a significant improvement of the biodegradability; consequently and even if the limit of biodegradability (0.4) was not achieved, a biological treatment could be promisingly considered. GRAPHICAL ABSTRACT
28 August 2020 in Reaction Kinetics, Mechanisms and Catalysis