Composites for efficient removal of hexavalent chromium Cr(VI) from industrial wastewater were obtained by deposition of nano-zero-valent iron (nZVI), synthesized by environmentally friendly synthesis using oak leaf extract, on inexpensive, natural, readily available and cheap natural raw materials, sepiolite (SEP) or kaolinite/illite (KUb) clay, as support. nZVI particles were deposited from the FeCl₃ solution of different concentrations, with the same volume ratio extract/FeCl₃ solution (3:1), and with different masses of SEP or KUb. Physico–chemical characterization (SEM/EDS, FTIR, BET, determination of point of zero charge) of the composites and nZVI was performed. The results of SEM and BET analyses suggested more homogeneous deposition of nZVI onto SEP than onto KUb, which ensures greater availability of the nZVI surface for Cr(VI) anions. Therefore, the higher Cr(VI) removal at all investigated initial pH values (pH_i) of the solution (3, 4 and 5) was achieved with the SEP composites. The adsorption results indicated that the elimination of Cr(VI) was achieved via the combined effect of reduction and adsorption. The removal of total chromium at pH_i = 3 was approximately the same as that of Cr(VI) removal for the KUb composites, but lower for the SEP composites, indicating lower removal of Cr(III) compared to the reduced Cr(VI). The SEP/nZVI composite with the highest removal efficiency was applied for Cr(VI) removal from real wastewater at pH_i = 3 and pH_i = 5. The results demonstrated the high Cr(VI) removal capacity, validated the assumption that a good dispersion of nZVI particles is beneficial for Cr(VI) removal and showed that the produced green composites can be efficient materials for the removal of Cr(VI) from wastewater.

The sepiolite/ZrO₂ composites were prepared by sepiolite (Sep) modification with zirconium propoxide in toluene at room temperature for 24 h (Sep–ZrI) or 95 °C for 4 h (sample Sep–ZrII). The efficiency of the obtained composites for the removal of phosphate from aqueous solutions at initial pH = 4 and pH = 8 was investigated. Characterization of the samples shows that synthesis at a higher temperature for a shorter time provides a slightly higher content of amorphous Zr phase, which is deposited on the sepiolite fibers as a thin layer and agglomerated nanoparticles. Compared to Sep, the composites have a lower point of zero charge and higher specific surface area and pore volume. The adsorption kinetics follow the pseudo second-order model. The adsorption capacities of the composites are approximately the same at both initial pH and higher at initial pH = 4 than at pH = 8. The XPS and ATR-FTIR of Sep–ZrI before and after adsorption identifies the formation of inner-sphere complexes as the mechanism of phosphate adsorption. The slow release during desorption with NaOH solution confirms the strong bonds of the phosphates with the surface of the composites.

In order to improve the mechanical properties of paper, 1, 3 and 5 wt.% of sepiolite were dispersed in a poly(vinyl butyral) (PVB) matrix and coated onto the surface of schrenz (110 g m-2). Deagglomerated sepiolite nanofibers in PVB matrix on paper surface were observed by scanning electronic microscopy. The glass transition temperature of schrenz with PVB/sepiolite coatings was not changed with increasing content of sepiolite. Two different methods were used to evaluate the mechanical properties of the paper sample reinforced with PVB/sepiolite nanocomposites: tensile testing and nanoindentation. The values of breaking force and tensile energy absorption of the reinforced paper samples obtained by tensile testing were increased by up 10 %. The values of the reduced elastic modulus and hardness obtained by nanoindentation were increased by up to 78 %. The best improvement of the mechanical properties was shown by the paper sample coated with PVB/3 wt.% sepiolite nanocomposite.

The microstructure–property relationship in poly(methyl methacrylate) PMMA composites is very important for understanding interface phenomena and the future prediction of properties that further help in designing improved materials. In this research, field emission scanning electron microscopy (FESEM) images of denture PMMA composites with SrTiO₃, MnO₂ and SrTiO₃/MnO₂ were used for fractal reconstructions of particle agglomerates in the polymer matrix. Fractal analysis represents a valuable mathematical tool for the characterization of the microstructure and finding correlation between microstructural features and mechanical properties. Utilizing the mathematical affine fractal regression model, the Fractal Real Finder software was employed to reconstruct agglomerate shapes and estimate the Hausdorff dimensions (HD). Controlled energy impact and tensile tests were used to evaluate the mechanical performance of PMMA-MnO₂, PMMA-SrTiO₃ and PMMA-SrTiO₃/MnO₂ composites. It was determined that PMMA-SrTiO₃/MnO₂ had the highest total absorbed energy value (E_tot), corresponding to the lowest HD value of 1.03637 calculated for SrTiO₃/MnO₂ agglomerates. On the other hand, the highest HD value of 1.21521 was calculated for MnO₂ agglomerates, while the PMMA-MnO₂ showed the lowest E_tot. The linear correlation between the total absorbed impact energy of composites and the HD of the corresponding agglomerates was determined, with an R² value of 0.99486, showing the potential use of this approach in the optimization of composite materials’ microstructure–property relationship.