With the increasing demand for space missions, space robots have become the focus of research and attention. As a typical representative, the free-floating dual-arm space robot has the characteristics of multiple degrees of freedom, a floating base, and dynamic coupling between the manipulator and the base, so its modeling and control are very challenging. To address these challenges, a novel dynamic modeling and control method is proposed for a free-floating dual-arm space robot. First, an explicit dynamic model of a free-floating dual-arm space robot is established based on the explicit canonical multi-rigid-body dynamic modeling theory and combined with the concept of a dynamic equivalent manipulator. The establishment process of this model is not only simple and canonical to avoid the definition and calculation of many intermediate variables, but the symbolic result expression of the model also has the characteristics of iteration, which is convenient for computer automatic modeling. Next, aiming at addressing the problem of trajectory tracking and the base attitude stability of a free-floating dual-arm space robot with parameter perturbation and external disturbance, an improved nonlinear model predictive control method introducing the idea of sliding mode variable structure is proposed. Theoretical analysis shows that the proposed controller has better robustness than the traditional nonlinear model predictive controller. Then, an in-orbit service task is designed to verify the effectiveness of the proposed dynamic modeling and control strategy of the free-floating dual-arm space robot. Finally, the dynamic modeling and control methods proposed are discussed and summarized. The proposed methods can not only realize the tracking of the desired trajectory of the arms of the free-floating space robot, but can also realize the stable control of the base of the free-floating space robot. This paper provides new insights into the difficult problems regarding the dynamics and control of free-floating dual-arm space robots.
This paper proposes a novel brake mechanism in robot joints, especially for space robot joints which require low power consumption and high reliability. The key point of the brake mechanism is that the torque spring is replaced with the Nd-Fe-B permanent magnet. Due to the position and force relationship between the permanent magnet and the electromagnet in the brake mechanism, the stroke of the brake armature can be extended so that the bolt type brake structure is adapted and the braking torque can be infinite theoretically. Meanwhile, the holding current in the electromagnet can be decreased to save energy and reduce heat generation. The magnetic circuit models of the electromagnet and permanent magnet in the brake mechanism are established and analyzed. In order to improve the response speed of the brake mechanism, a novel H-bridge brake power supply circuit is proposed. To verify the benefits of the design, a permanent magnet brake prototype with the H-bridge power supply circuit is set up. While the holding current is consistent with the peak current in the conventional torque spring motor brake, the proposed permanent magnet brake mechanism can decrease the holding current below 0.1 A.
Friction is an inevitable phenomenon in mechanical systems that affects the dynamic characteristics of systems. To reduce the modeling complexity of complex multi-rigid-body mechanisms, a novel explicit canonical dynamic modeling method considering joint friction is proposed. Based on the explicit dynamic modeling theory that we have proposed, the solution of the constraint force required by the joint friction modeling of multi-rigid-body mechanisms is derived and improved, which greatly simplifies the solution of the constraint force. According to the obtained explicit expression of the constraint force equations, two joint friction models of the Coulomb–viscous effect and Stribeck effect are derived in analytical form. Moreover, the Stribeck effect of the joint is experimentally analyzed. A five-axis tree-chain mechanism and a three-loop closed-chain mechanism are chosen to demonstrate the method and compared with ADAMS software. Moreover, the proposed model is analyzed and compared with other methods.
8 April 2022 in International Journal of Non-Linear Mechanics
This paper proposes a novel PM-electromagnet brake with rolling balls embedded in the friction plate, which has significant advantages of higher torque-to-size ratio, lower power consumption and quicker brake response speed. The structural innovations of the proposed brake are mainly reflected in the following two aspects: 1. The torque springs are replaced by high-performance PMs to reduce power consumption during Brake-Holding Mode; 2. Rolling-balls are embedded in the friction plate to increase the braking torque. In addition, an optimized brake circuit is designed to improve the brake response speed by shortening the inductor discharging time. Firstly, the structural innovations of proposed brake are presented and discussed in detail. Then, theoretical analysis mainly focuses on the following two aspects: 1. How the rolling ball-embedded structure can improve the torque-to-size ratio; 2. How the distributed PMs can reduce the power consumption during Brake-Holding Mode. At last, the optimized brake circuit is given. To verify the benefits of the design, a proposed brake prototype is manufactured, as well as the optimized brake circuit. The experimental result is promising, and the proposed brake is suitable for various applications.