This paper presents a new transmitter architecture based on digital-Intermediate Frequency (IF) High-Pass Delta-Sigma Modulator (HPDSM). The proposed digital-IF transmitter topology utilizes a novel Complex HPDSM topology to address the high quantization-noise power problem in Cartesian Band-pass BPDSM and HPDSM-based digital-IF transmitters, without increasing the oversampling ratio (OSR) of the signal or the clock rate of the system. To evaluate the performance of the new digital-IF transmitter system, a comparison with its Cartesian Band-pass and High-Pass counterparts, in terms of Signal to Noise and Distortion Radio (SNDR) and Coding Efficiency (CE), was established. A simulation using 8 dB Peak to Average Power Ratio (PAPR) Long Term Evolution (LTE) signals with 1.24 MHz bandwidth showed that by integrating the proposed second-order Complex HPDSM digital-IF in the transmitter, the power of the quantization noise is significantly reduced. The transmitter digital blocks were implemented on the BEEcube Software Defined Radio (SDR) prototyping platform. The input signal is encoded by the new HPDSM topology and is up-converted and then fed to the inverse class-F Switch-Mode Power Amplifier (SMPA). An overall efficiency of 12% was achieved by the proposed topology. Moreover, the output signal SNDR reached 37.8dB and the Adjacent Channel Leakage Ratio (ACLR) at the lower and upper 1.25 MHz offset frequencies measured is equal to -35 dBc.
This paper presents an implementation of an all-digital transmitter architecture for software defined radio (SDR) applications. This transmitter uses a first order, sigma-delta modulator for one-bit quantization and noise shaping. The binary signal is passed through high-speed multiplexing circuits for frequency upconvertion directly from base-band to the desired carrier frequency [1]. This digital implementation has interesting features such as reconfigurability as well as preserving a good signal quality, at an additional expense of the high speed components required to perform oversampling and multiplexing. The behavior of the all-digital transmitter is simulated and measured using a baseband signal having 1.94 MHz bandwidth up-converted to 2.5 GHz carrier frequency. The implementation steps are shown along with the obtained simulation and measurement results. The overall linearity performance are given in terms of gain response, signal-to-noise-and-distortion ratio (SNDR) and the adjacent-channel-power ratio (ACPR).
In this paper, a dual-branch topology driven by a Delta-Sigma Modulator (DSM) with a complex quantizer, also known as the Complex Delta Sigma Modulator (CxDSM), with a 3-level quantized output signal is proposed. By de-multiplexing the 3-level Delta-Sigma-quantized signal into two bi-level streams, an efficiency enhancement over the operational frequency range is achieved. The de-multiplexed signals drive a dual-branch amplification block composed of two switch-mode back-to-back power amplifiers working at peak power. A signal processing technique known as quantization noise reduction with In-band Filtering (QNRIF) is applied to each of the de-multiplexed streams to boost the overall performances; particularly the Adjacent Channel Leakage Ratio (ACLR). After amplification, the two branches are combined using a non-isolated combiner, preserving the efficiency of the transmitter. A comprehensive study on the operation of this topology and signal characteristics used to drive the dual-branch Switch-Mode Power Amplifiers (SMPAs) was established. Moreover, this work proposes a highly efficient design of the amplification block based on a back-to-back power topology performing a dynamic load modulation exploiting the non-overlapping properties of the de-multiplexed Complex DSM signal. For experimental validation, the proposed de-multiplexed 3-level Delta-Sigma topology was implemented on the BEEcube™ platform followed by the back-to-back Class-E switch-mode power amplification block. The full transceiver is assessed using a 4th-Generation mobile communications standard LTE (Long Term Evolution) standard 1.4 MHz signal with a peak to average power ratio (PAPR) of 8 dB. The dual-branch topology exhibited a good linearity and a coding efficiency of the transmitter chain higher than 72% across the band of frequency from 1.8 GHz to 2.7 GHz.
3 December 2018 in Microwave and Optical Technology Letters