Hemispherical Resonator Gyroscope (HRG) represents a new type of inertial sensor. The vibrational properties of the hemispherical resonator, a core component of the HRG, significantly influence the output accuracy of the gyroscope. This paper is the first to integrate the effects of residual stress nonuniformity and mass nonuniformity in a unified model for hemispherical resonator. Firstly, the equation of motion for the resonator with these nonuniformities are derived based on the thin shell theory and the Lagrange equation. Then, two important vibration parameters, including the frequency split and the azimuth of stiffness axis, are calculated by a novel method based on the unified model. Next, the detailed simulations are conducted, which reveals that the frequency split is directly proportional to the fourth harmonic magnitude of mass or residual stress nonuniformity alone, with the azimuth of stiffness axis aligning with their initial phase (or differing by 22.5° for shear stress). However, under coupled nonuniformities, the frequency split depends nonlinearly on both fourth harmonics, while the azimuth of stiffness axis exhibits complex nonlinear behavior, with coupling strength critically influenced by their phase difference. Finally, based on the least squares method, an identification scheme for the error parameters associated with residual stress nonuniformity is designed. The experimental results show good consistency with the theoretical predictions, which confirms the correctness of the dynamic model and error analysis. This study addresses practical limitations of existing models and provides a theoretical foundation and experimental guidance for the optimization of the manufacturing processes of high-precision HRG.
This paper studied the primary sources, evolution rules, and influence mechanisms of the damping anisotropy of the whole-angle hemispherical resonator gyroscope from the perspective of the fabrication process and analyzed the influence of temperature change on the damping anisotropy. An error identification and compensation method is proposed to suppress the effect of the damping anisotropy error on the gyroscope's bias error. According to the energy controller's output, this method involves applying the recursive least squares method to identify the damping anisotropy error and the damping axis angle in real time. Subsequently, a compensation signal is synthesized based on the identification results and applied to the angular rate control loop to compensate for the damping asymmetry error online. The experimental results show that the peak-to-peak value of the angular rate output harmonic error of the gyroscope is reduced from 0.023°/s to 0.005°/s after the error compensation, which is an improvement of about 5 times. In addition, the peak-to-peak value of the gyroscope angular dependent bias error decreases from 0.7072° to 0.08268°, which improves by 8.55 times, and the linearity of the angular measurements is also significantly improved. This methodology can be widely applied to gyroscopes operating in whole-angle mode, which is essential for fundamentally reducing the bias errors of the gyroscope induced by damping asymmetry.
The properties of small size, low noise, high performance and no wear-out have made the hemispherical resonator gyroscope a good choice for high-value space missions. To enhance the precision of the hemispherical resonator gyroscope for use in tasks with large angular velocities and angular accelerations, this paper investigates the standing wave precession of a non-ideal hemispherical resonator under nonlinear high-intensity dynamic conditions. Based on the thin shell theory of elasticity, a dynamic model of a hemispherical resonator is established by using Lagrange’s second kind equation. Then, the dynamic model is equivalently transformed into a simple harmonic vibration model of a point mass in two-dimensional space, which is analyzed using a method of averaging that separates the slow variables from the fast variables. The results reveal that taking the nonlinear terms about the square of the angular velocity and the angular acceleration in the dynamic equation into account can weaken the influence of the 4th harmonic component of a mass defect on standing wave drift, and the extent of this weakening effect varies with the dimensions of the mass defects, which is very important for steering the development of the high-precision hemispherical resonator gyroscope.
1 January 2021 in Journal of Physics: Conference Series
Surface cleaning is an essential procedure to improve quality and performance of workpiece in modern industrial manufacturing. Among surface cleaning technologies, laser cleaning has been regarded as the most promising green cleaning technology. Laser cleaning is a green cleaning technology that will not cause any environmental pollution. Laser cleaning has the ability of cleaning the area of the designated shape. A set of laser cleaning system that consists of two-dimensional galvanometer and 3-axis motion platform, was designed in this paper. The two-dimensional galvanometer was used to clean the area of the specified shape. The 3-axis motion platform expands the limited cleaning area of the two-dimensional galvanometer to a larger area. Laser displacement sensor is utilized to ameliorate the cleaning quality. To improve the cleaning accuracy of the system proposed in this article, a camera was adopted to recognize the origin of the workpiece and correct the pose of the workpiece. Experimental results demonstrate the performance of the proposed system for large-scale plane workpiece.
1 January 2026 in IEEE Transactions on Instrumentation and Measurement