Jianyu Li

Dr. Jianyu Li

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 August 2023 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
YQYusheng Qin
Yusheng Qin
ZYZhaoxiang Yan
Zhaoxiang Yan
QWQihua Wu
Qihua Wu
AJAilong Jiang
Ailong Jiang
YLYujuan Li
Yujuan Li
JLJianyu Li
Jianyu Li

21 June 2024 in Progress in Natural Science: Materials International
Verified
Journal Article
Closed access
SLShulin Lü
Shulin Lü
SLShilong Li
Shilong Li
ZYZhaoxiang Yan
Zhaoxiang Yan
SWShusen Wu
Shusen Wu
JLJianyu Li
Jianyu Li
XJXiaoyuan Ji
Xiaoyuan Ji

13 March 2024 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
SLShulin Lü
Shulin Lü
SLShilong Li
Shilong Li
JQJian Qin
Jian Qin
DZDijia Zhao
Dijia Zhao
JLJianyu Li
Jianyu Li
SWShusen Wu
Shusen Wu

10 January 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
RWRui Wang
Rui Wang
PXPeijie Xiao
Peijie Xiao
HLHao Li
Hao Li
HSHua Song
Hua Song
HLHouguo Lu
Houguo Lu
SXShiwei Xu
Shiwei Xu

7 October 2022 in Materials
Verified
Journal Article
Open access
PDF file
QLQiao Liao
Qiao Liao
JLJianyu Li
Jianyu Li
JLJianping Liu
Jianping Liu
SLShulin Lü
Shulin Lü
LCLu Chen
Lu Chen
Shusen WuShusen Wu
Shusen Wu
In this paper, the refinement effect of Al-5Ti-0.2C refiner on Al-Zn-Mg-Cu alloys was first investigated, and then the effects of three forming processes, i.e., Gravity Casting (GC), Squeeze Casting (SC), and Squeeze Casting after Ultrasonic Treatment (UT-SC), on microstructure and properties of Al-Zn-Mg-Cu alloys were studied. The results show that the refining effect of Al-5Ti-0.2C refiner is obvious; first, the average grain size of the alloy decreases and then increases with the increase in Ti content from 0.15 wt.% to 0.3 wt.%. The optimal amount of added Al-5Ti-0.2C is 0.2 wt.% Ti content. The good refining effect is attributed to the formation of TiC particles and Al3Ti compounds by the refiner, which can all be the nucleus of solidification. The poor refining effect when the Ti content was more than 0.2 wt.% is due to the formation of coarse Al3Ti particles. The results of three forming processes that cast Al-Zn-Mg-Cu alloys under the addition of Al-5Ti-0.2C with 0.2 wt.% Ti content show that the mechanical properties under the UT-SC process are the best; the tensile strength in the as-cast state reaches 367 MPa, and the elongation is 3.84%. The effect of tiny TiC particles in the refiner on the microstructure and properties of Al-Zn-Mg-Cu alloys is also discussed.

13 April 2021 in Metals
Verified
Journal Article
Open access
PDF file
CLCheng Li
Cheng Li
Shusen WuShusen Wu
Shusen Wu
SLShulin Lü
Shulin Lü
JLJianyu Li
Jianyu Li
LLLongfei Liu
Longfei Liu
LXLanqing Xia
Lanqing Xia
The Zr element is one of the important grain refiners for 7xxx series Al-Zn-Mg-Cu alloys, but the effect of Zr content more than 0.15 wt.% needs to be deeply investigated under the action of ultrasonic vibration. In this study, the effects of Zr contents (0.1 to 0.25 wt.%) on microstructure and mechanical properties of Al-Zn-Mg-Cu alloy were studied. The results showed that Zr element could refine grains, but when the Zr content was greater than 0.15 wt.%, the grain size was not uniform, the number of second phase particles increased, and the segregation of components became more serious. It was found that after ultrasonic treatment, the grain-size inhomogeneity was greatly improved, and the Zr content could be added up to 0.2 wt.%. When the Zr content is equal or lower than 0.2 wt.%, ultrasonic treatment can effectively improve the mechanical properties of materials by refining grains and weakening segregation. However, when the Zr content is up to 0.25 wt.%, the effect is getting worse.