An afterburner encounters two primary features: high incoming flow velocity and low oxygen concentration in the incoming airflow, which pose substantial challenges and contribute significantly to the deterioration of combustion performance. In order to research the influence of oxygen content on the dynamic combustion characteristics of the afterburner under various inlet velocities, the effect of oxygen content (14–23%) on the field structure of reacting bluff body flow, flame morphology, temperature pulsation, and pressure pulsation of the afterburner at different incoming flow velocities (0.1–0.2 Ma) was investigated in this study by using a large eddy simulation method. The results show that two different instability features, BVK instability and KH instability, are observed in the separated shear layer and wake, and are influenced by changes in the O2 mass fraction and Mach number. The oxygen content and velocity affected the oscillation amplitude of the downstream flow. As the O2 mass fraction decreases, the flame oscillation amplitude increases, the OH concentration in the combustion chamber decreases, and the flame temperature decreases. Additionally, the amplitude of the temperature pulsation in the bluff body flame was primarily influenced by the temperature intensity of the flame and BVK instability. Moreover, the pressure pulsation is predominantly affected by the dynamic characteristics of the flow field behind the bluff body. When the BVK instability dominated, the primary frequency of the pressure pulsation aligned with that of the temperature pulsation. Conversely, under the dominance of the KH instability, the temperature pulsation did not exhibit a distinct main frequency. At present, the influence of oxygen content and incoming flow rate on the combustion performance of the combustion chamber is not clear. The study of the effect of oxygen content on the combustion characteristics of the combustion chamber at different incoming flow rates provides a reference for improving the performance of the combustion chamber and enhancing the combustion stability.
In this study, large eddy simulation (LES) was used to investigate the dynamic characteristics of diffusion flames in a swirl combustion chamber at an oxygen content of 11–23 wt% and temperature of 770 K. The proper orthogonal decomposition (POD) method was employed to obtain flame dynamic modes. The results indicate that oxygen content has a significant impact on the downstream flow and flame combustion characteristics of the swirl combustion chamber. With oxygen content increasing, the size of the recirculation zone is reduced, and the flame field fluctuations are intensified. The pressure and heat release fluctuations under different oxygen contents were analyzed using frequency spectrum analysis. Finally, the flame modes were analyzed using the POD method, and it was found that the coherent structures are asymmetric relative to the local coordinate system. At an oxygen content of 11 wt%, they exhibit larger coherent structures, while at an oxygen content of 23 wt%, they exhibit numerous turbulent structures.
Gas turbines are widely used as important equipment for electricity generation on islands and offshore platforms. During the operation of a gas turbine, the flame shape in the combustion chamber undergoes variations in response to changes in parameters such as gas turbine load, fuel distribution, and burner structure. These alterations in flame shape exert influence on combustion instability, emissions, and load characteristics. This study explores the variations in flame transition, emissions, and operating parameters among three distinct center stage structures: namely, the non-premix center stage (NPCS), premix center stage (PCS), and enhanced premix center stage (PCSE). The investigation is conducted using a heavy-duty gas turbine hybrid burner on a full temperature, full pressure, and full-size single burner experimental bench. Simultaneously, a multi-parameter numerical simulation regarding the influence of the central fuel split on flame shape analysis was conducted using the PCS burner under the design point for a more in-depth understanding of the mechanisms and for influencing factors associated with flame transition. The findings indicate that variations in flame transition loads among different central stage structures: for the NPCS burner, the transition occurs between 45% and 50% load; for the PCS burners, it takes place between 60% and 65% load; for the PCSE burners, it shifts between 55% and 60% load. Additionally, a reduction in NOx emissions is observed during the flame transition process. Furthermore, it was found that decreasing the central stage fuel results in a decline in flame angle for the same burner structure. As the central stage fuel diminishes to a specific value, the flame shape undergoes a sudden change. Further reduction in central stage fuel does not significantly affect the flame shape and temperature distribution.