With the rapid development of the electric vehicle industry, the widespread utilization of lithium-ion batteries has made it imperative to address their safety issues. This paper focuses on the thermal safety concerns associated with lithium-ion batteries during usage by specifically investigating high-capacity lithium iron phosphate batteries. To this end, thermal runaway (TR) experiments were conducted to investigate the temperature characteristics on the battery surface during TR, as well as the changes in battery mass and expansion rate before and after TR. Meanwhile, by constructing a TR simulation model tailored to lithium iron phosphate batteries, an analysis was performed to explore the variations in internal material content, the proportion of heat generation from each exothermic reaction, and the influence of the heat transfer coefficient during the TR process. The results indicate that as the heating power increases, the response time of lithium-ion batteries to TR advances. Furthermore, the heat released from the negative electrode–electrolyte reaction emerges as the primary heat source throughout the entire TR process, contributing to 63.1% of the total heat generation.
In order to improve the aerodynamic performance of the voluteless centrifugal fan, a multi-objective optimization design system was established by combining parametric modeling, experimental design, surrogate models, and optimization algorithms, with the static pressure and static pressure efficiency of the fan as the optimization objectives. The design parameters of the blade profile were obtained by fitting the blade profile with a Bézier curve. A mapping relationship between design parameters and optimization objectives was established by combining numerical simulation with a radial basis function neural network, and a genetic algorithm was used to optimize the blade profile. The results indicated a highly significant correlation between design parameters and optimization objectives, with a prediction error of no more than 1% for the surrogate model. The determination coefficients for static pressure and static pressure efficiency were 0.98 and 0.96, respectively. After optimization, the static pressure of the fan increased by 12.7 Pa at the design operating point, and the static pressure efficiency increased by 3.2%. The separation vortex decreased near the trailing edge of the blade suction surface, and the airflow impact at the leading edge of the blade decreased. The entropy production in the flow channel decreased, and the overall flow state of the fluid was improved.
This paper uses modal analysis and harmonic response analysis to study the vibration characteristics and vibration response of the frame of a volute-less centrifugal fan. The accuracy of the finite element model is verified by comparing the experimental results with the numerical simulation results. Our focus is on the resonance behavior of the fan frame under the maximum operating conditions. Therefore, the structural parameters are taken as design variables, and the maximum axial amplitude at 2600 rpm and its corresponding axial modal frequencies are taken as target parameters for research. A combination of response surface methodology and multi-objective optimization is used to optimize the structure parameters and solve for the Pareto solution set. Three feasible solutions were selected to verify the method’s accuracy. The results show that the optimized fan frame structure enhances the axial modal frequencies to 52.3 Hz, reflecting a 24% improvement over the baseline. Furthermore, we reduce the maximum vibration velocity at resonance to 2.15 mm/s, effectively minimizing vibration responses and preventing excitation and resonance issues at peak speeds.
This paper proposes a multi-objective optimization method based on response surface methodology and genetic algorithm to address the electromagnetic noise issue in external rotor permanent magnet synchronous motors. Theoretical analysis and 2D finite element simulation of electromagnetic force were conducted to identify the main orders of electromagnetic force; subsequently, through motor load and no-load tests, it was determined that the 6th-order radial electromagnetic force is the primary source of electromagnetic noise. Taking the 6th-order radial electromagnetic force, average torque, and torque ripple as optimization objectives, three key structural parameters were selected from eight optimization variables to construct a response surface model. The structural parameter optimization scheme for the motor was then obtained using a genetic algorithm. Finally, the optimization scheme obtained by the response surface method was validated under motor load conditions using two-dimensional finite element simulation; simulation results indicate that, compared to the original design, the optimized motor, exhibits a reduction in torque ripple by 65%, with the harmonic content of the radial air-gap flux density at the 1st, 3rd, 5th, and 7th orders decreasing by 8.7%, 6.4%, 12.5%, and 10.7%, respectively, and the 6th-order radial electromagnetic force reduced by 16.4%. Based on experimental identification of the dominant noise source, this reduction is expected to effectively suppress electromagnetic noise, which will be validated on a prototype in future work.
This study addresses the thermal safety issues of ternary lithium-ion batteries, focusing on NCM523 monomer lithium-ion batteries as the research subject. A thermal abuse model for lithium-ion batteries is established, and thermal Oven experiments are simulated to investigate the thermal runaway (TR) process of lithium-ion batteries under high-temperature conditions (135°C ~ 195°C). The study analyzes the impact of various factors such as environmental temperature, state of charge (SOC) of the battery, initial battery temperature, and heat transfer coefficient on the thermal runaway of lithium-ion batteries. Additionally, it examines the changes in the internal material content of the battery and heat generation in various parts of the battery during the thermal runaway process. The research reveals that at an oven temperature of 195°C, the maximum temperature during the thermal runaway of lithium-ion batteries can reach approximately 625°C. The reactions between the negative electrode and electrolyte, as well as the positive electrode and electrolyte, are the primary sources of heat generation during thermal runaway. An increase in the state of charge of the battery leads to an earlier onset of thermal runaway. Furthermore, an increase in the heat transfer coefficient results in an earlier onset of thermal runaway. Implementing appropriate cooling methods (liquid cooling or direct cooling) can to some extent prevent the occurrence of thermal runaway phenomena.