The composition and micromechanical properties of rock minerals have important effects on its macroscopic mechanical performance. The composition, proportions, and morphology of sandstone minerals are determined using an energy dispersive spectrometer and optical microscopy. The elastic modulus and hardness of each mineral component are then measured through nanoindentation tests. The equivalent elastic modulus and Poisson's ratio of sandstone are obtained using the dilute and Mori–Tanaka homogenization schemes and compared with the elastic modulus and Poisson's ratio measured in uniaxial compression tests. Finally, the influence of various microscopic parameters on the macroscopic mechanical properties of sandstone is analyzed. The results indicate that sandstone is mainly composed of quartz, feldspar, biotite, and chlorite, which can be distinguished and recognized by color and morphological characteristics under an optical microscope. Quartz has a dense structure and good mechanical properties, while biotite and chlorite have obvious pore structures and the worst mechanical properties. The equivalent Poisson's ratio obtained by homogenization is basically consistent with the macroscopic Poisson's ratio measured through testing, but the equivalent elastic modulus is greater than the test results. The Mori–Tanaka scheme gives the largest deviation in the equivalent elastic modulus. Parameter analysis shows a positive correlation between the microscopic and macroscopic mechanical properties of each mineral component. The volume fractions of quartz and feldspar are positively correlated with the macroscopic mechanical properties, while chlorite exhibits a negative correlation. The macroscopic mechanical properties of sandstone are most sensitive to changes in the mechanical properties and volume fraction of chlorite.
Fracture and stress environments significantly affect the flow of coalbed methane. Under stress, fracture deformation and damage occur, which change the original fracture characteristics and lead to changes in gas flow characteristics. The change in gas pressure gradient makes the fluid flow obviously nonlinear. Using linear flow theory to describe the fracture flow leads to a large error in predicting coalbed methane productivity. In this study, seepage tests on fractured coal are carried out under different stresses and gas pressure gradients, the nonlinear flow and changes in related parameters are analyzed, and the applicability of the nonlinear flow equation is evaluated. The resulting seepage of the gas flow in the fracture under stress is obviously nonlinear, which gradually increases with increasing effective stress and gas pressure gradient. When the Forchheimer equation is used to characterize the nonlinear seepage in fractures, the coefficients increase with increasing effective stress. The permeability, nonlinear factor, and critical Reynolds number decrease with increasing effective stress. When the Izbash equation is used for this case, the linear coefficient ranges from 1015 to 1016, and the nonlinear coefficient ranges from 1.064 to 1.795. The coefficients are related to the effective stress through a power function. Both the Forchheimer and Izbash equations can characterize the flow in rough fractures in coal during stress loading. However, the Forchheimer equation better reveals the mechanism of flow transformation from linear to nonlinear in fractures.
Distinct from hard rock, coal is relatively soft and fragmented. It is not only challenging to prepare test coal samples that meet the requirements of standard mechanical experiments but also impossible to recycle them for repeated testing. There is an urgent need to explore new mechanical testing methods to enhance the study of the mechanical properties of coal. In this study, the micromechanical parameters of the coal matrix solid phase were acquired through targeted nanoindentation technology. The elemental composition, surface morphology, and pore structure characteristics of each indentation point were determined by energy dispersive spectrometer, optical microscope observation, and high-pressure mercury injection experiments. The fractal homogenization equation is deduced based on fractal geometry and the Mori–Tanaka method. The validity of the fractal homogenization approach is verified by integrating the micromechanical parameters and pore structure characteristics of coal, and the impact of the microstructural parameters on the macroscopic mechanical properties of coal is discussed. The results show that the proportion of clay minerals in the solid phase of the coal is the greatest (81.18%), with the main mineral components being kaolinite and illite. The elastic modulus is 1.974 ± 1.036 GPa, the hardness is 0.131 ± 0.108 GPa, and the ratio of upper and lower pore scales conforms to the fractal calibration rate. The macroscopic equivalent elastic modulus rises along with the increase in the fractal dimension. When the fractal dimension is constant, the macroscopic equivalent elastic modulus decreases with the increase in λmin/λmax and increases with the increase in solid phase elastic modulus.
The natural fracture network within the coal body serves as the main pathway for gas migration, with its geometric characteristics significantly impacting coalbed methane flow. In order to enhance the numerical model for simulating coalbed methane flow based on fracture network images, we define porosity and permeability functions for these images and improve upon existing methods. By employing a pixel probability decomposition algorithm, we establish a geometric model of a rough discrete fracture network, which is imported into COMSOL Multiphysics to build a numerical model of gas flow. We analyze the impact of different fracture structures on coal seam permeability and find that gas primarily flows through interconnected fractures at much higher velocities compared to matrix pores. Furthermore, we observe that fracture network permeability increases with increasing porosity (0.0635–0.164), fractal dimension (1.571–1.755), maximum fracture branch length (0.0111–0.0249 m), and connectivity (0.808–2.789). Conversely, it decreases with an increasing fracture dip angle (1.61–88.39°) and tortuosity fractal dimension (1.0018–1.0195). Our simulation method based on fracture network imaging provides a simple yet feasible approach to simulate gas extraction while accurately capturing various stages in the extraction process, including the temporal and spatial evolution of gas velocity and pressure as well as differences between fractures and the coal matrix.
Inorganic mineral pores in coal are highly effective conduits for the transport of methane and water but are primary sites for water blocking. Current research on methane/water two-phase flow in coal focuses on pores in organic matter, and few studies have been performed on inorganic mineral pores. Inorganic materials are typically hydrophilic, making it essential to investigate the distribution and transport of two-phase flow in inorganic mineral nanofluidic channels. In this study, a nanoscale kaolinite slit model was constructed using results from scanning electron microscopy and energy dispersive spectroscopy Molecular dynamics simulations were conducted on methane and water in the model. The influence of water saturation, pressure differential, and pore size on two-phase flow was systematically analyzed. Water molecules preferentially adsorb onto the surface of kaolinite channels. With increasing water saturation, the water molecules order into various structures, such as films, bridges, and locks. The presence of water substantially reduces the space available for methane flow. As the water saturation increases, for methane, the peak density near the channel walls decreases, the distribution gradually becomes parabolic, and the flow rate decreases considerably (particularly for 0–45% water saturation). At 45% water saturation, the methane flow rate is 69.46% lower than that for single-phase methane flow. Both the water and methane flow rates increase with the pore size, but the effect is stronger for water than for methane. These findings provide valuable insights into the underlying mechanisms of water blockage and could make production performance prediction more accurate.