The heterojunction based on n-TiO2 nanolayer/p-CuMnO2 thin film was achieved using an efficient two-step synthesis process for the fabrication of a UV photodetector. The first step consisted of obtaining the TiO2 nanolayer, which was grown on titan foil by thermal oxidation (Ti-TiO2). The second step consisted of CuMnO2 thin film deposition onto the surface of Ti-TiO2 using the Doctor Blade method. Techniques such as X-ray diffraction, UV-VIS analysis, SEM, and AFM morphologies were used for the investigation of the structural and morphological characteristics of the as-synthesized heterostructures. The Mott–Schottky analysis was performed in order to prove the n-TiO2/p-CuMnO2 junction. The I-V measurements of the n-TiO2 nanolayer/p-CuMnO2 thin film heterostructure confirm its diode characteristics under dark state, UV and visible illumination conditions. The obtained heterojunction, which is based on two types of semiconductors with different energy band structures, improves the separating results of charges, which is very important for high-performance UV photodetectors.
The present study investigates the possibility to apply a vacuum furnace thermal post-treatment as an alternative solution for flame sprayed NiCrBSi wear and corrosion-resistant coatings, deposited on a low alloyed structural steel. The controlled atmosphere offers advantages regarding the fusion of the coating, porosity reduction, and degassing. An improvement of the applied heating-cooling cycle was performed through the variation of time and temperature. The best performing samples were selected by comparing their porosity and roughness values. The chosen samples were subsequently characterized regarding their microstructure, microhardness, sliding wear, and corrosion behavior. The experimental work confirms that the use of a vacuum remelting post-process reduces the porosity below 1% and leads to the formation of a larger quantity of hard boron-containing phases, promoting a significant decrease of the wear rate, while maintaining a good corrosion behavior.
A flexible electrode constructed from Fe-based amorphous ribbons decorated with nanostructured iron oxides, representing the novelty of this research, was successfully achieved in one-step via a chemical oxidation method, using a low concentration of NaOH solution. The growth of metal oxides on a conductive substrate, which forms some metal/oxide structure, has been demonstrated to be an efficient method for increasing the charge transfer efficiency. Through the control and variation of synthetic parameters, different structures and morphologies of iron oxide were obtained, including hexagonal structures with a hollow ball shape and rhombohedral structures with rhombus-like shapes. Structural and morphological characterization methods such as X-ray diffraction and SEM morphology were used on the as-synthesized composite materials. The supercapacitor properties of the as-developed amorphous ribbons decorated with Fe2O3 nanoparticles were investigated by cyclic voltammetry, galvanostatic charge discharge, and electrochemical impedance spectroscopy. The flexible supercapacitor negative electrode demonstrates a specific capacitance of 5.96 F g−1 for the 0.2 M NaOH treated sample and 8.94 Fg−1 for the 0.4 M NaOH treated sample. The 0.2 M treated negative electrodes deliver 0.48 Wh/kg at a power density of 20.11 W/kg, and the 0.4 M treated electrode delivers 0.61 Wh/kg at a power density of 20.85 W/kg. The above results show that these flexible electrodes are adequate for integration in supercapacitor devices, for example, as negative electrodes.
A self-powered photodetector with the FTO/n-TiO2/p-CuMnO2 configuration, representing the novelty of the work, was successfully achieved for the first time and presumes two steps: deposition of the n-type semiconductor (TiO2) by the doctor blade method and of the p-type semiconductor (CuMnO2) by the spin coating technique, respectively. Investigation techniques of the structural and morphological characteristics of the as-synthesized heterostructures, such as XRD, UV-VIS analysis, and SEM/EDX and AFM morphologies, were used. The I-t measurements of the photodetector showed that the responsivity in the self-powered mode was 2.84 × 107 A W−1 cm2 and in the 1 V bias mode it was 1.82 × 106 A W−1 cm2. Additionally, a self-powered current of 14.2 nA was generated under UV illumination with an intensity of 0.1 mW/cm2. Furthermore, under illumination conditions, the response time (tres) and the recovery time (trec) of the sensor exhibited a good response; thus, tres = 7.30 s and trec = 0.4 s for the self-powered mode, and in the 1 V bias mode, these were tres = 15.16 s and trec = 2.18 s. The above results show that the transparent heterojunction device of n-TiO2/p-CuMnO2 exhibited a self-powered ultraviolet photodetector with high sensitivity.
Ni-based alloys are among the materials of choice in developing high-quality coatings for ambient and high-temperature applications that require protection against intense wear and corrosion. The current study aims to develop and characterize NiCrBSi coatings with high wear resistance and improved adhesion to the substrate. Starting with nickel-based feedstock powders, thermally sprayed coatings were initially fabricated. Prior to deposition, the powders were characterized in terms of microstructure, particle size, chemical composition, flowability, and density. For comparison, three types of powders with different chemical compositions and characteristics were deposited onto a 1.7227 tempered steel substrate using oxyacetylene flame spraying, and subsequently, the coatings were inductively remelted. Ball-on-disc sliding wear testing was chosen to investigate the tribological properties of both the as-sprayed and induction-remelted coatings. The results reveal that, in the case of as-sprayed coatings, the main wear mechanisms were abrasive, independent of powder chemical composition, and correlated with intense wear losses due to the poor intersplat cohesion typical of flame-sprayed coatings. The remelting treatment improved the performance of the coatings in terms of wear compared to that of the as-sprayed ones, and the density and lower porosity achieved during the induction post-treatment had a significant positive role in this behavior.
The present study aimed to investigate the tribological behavior of high-temperature vacuum-brazed WC-Co-NiP functional coatings deposited on 16MnCr5 case hardening steel. Dry sliding wear resistance was evaluated using a non-conformal ball-on-disk arrangement, at room temperature against 100Cr6 and WC-Co static partners, respectively. Morphological, microstructural, and chemical composition analyses showed a complex, phased structure composed of tungsten carbide, nickel, and hard cobalt-based η-structure. In the testing conditions, the coefficient of friction against 100Cr6 and WC-Co counterparts entered a steady-state value after approximately 1000 m and 400 m, respectively. The wear track analysis revealed phenomena of particles trapped between the sliding bodies, as well as gradual removal of asperities. The calculations of the wear rates proved that the values were strongly influenced by properties of the sliding system, such as crystal structure, stress discontinuities, hardness, and material homogeneity.