Jan Sobieski

Mr. Jan Sobieski

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2021 in Coatings
Verified
Journal Article
Open access
PDF file
WGWaldemar Gawron
Waldemar Gawron
JSJan Sobieski
Jan Sobieski
TMTetiana Manyk
Tetiana Manyk
MKMałgorzata Kopytko
Małgorzata Kopytko
PMPawel Madejczyk
Pawel Madejczyk
JRJarosław Rutkowski
Jarosław Rutkowski
This paper presents the current status of medium-wave infrared (MWIR) detectors at the Military University of Technology’s Institute of Applied Physics and VIGO System S.A. The metal–organic chemical vapor deposition (MOCVD) technique is a very convenient tool for the deposition of HgCdTe epilayers, with a wide range of compositions, used for uncooled infrared detectors. Good compositional and thickness uniformity was achieved on epilayers grown on 2-in-diameter, low-cost (100) GaAs wafers. Most growth was performed on substrates, which were misoriented from (100) by between 2° and 4° in order to minimize growth defects. The large lattice mismatch between GaAs and HgCdTe required the usage of a CdTe buffer layer. The CdTe (111) B buffer layer growth was enforced by suitable nucleation procedure, based on (100) GaAs substrate annealing in a Te-rich atmosphere prior to the buffer deposition. Secondary-ion mass spectrometry (SIMS) showed that ethyl iodide (EI) and tris(dimethylamino)arsenic (TDMAAs) were stable donor and acceptor dopants, respectively. Fully doped (111) HgCdTe heterostructures were grown in order to investigate the devices’ performance in the 3–5 µm infrared band. The uniqueness of the presented technology manifests in a lack of the necessity of time-consuming and troublesome ex situ annealing.

25 January 2022 in Sensors
Verified
Journal Article
Open access
PDF file
MKMałgorzata Kopytko
Małgorzata Kopytko
JSJan Sobieski
Jan Sobieski
WGWaldemar Gawron
Waldemar Gawron
PMPiotr Martyniuk
Piotr Martyniuk
The trend related to reach the high operating temperature condition (HOT, temperature, T > 190 K) achieved by thermoelectric (TE) coolers has been observed in infrared (IR) technology recently. That is directly related to the attempts to reduce the IR detector size, weight, and power dissipation (SWaP) conditions. The room temperature avalanche photodiodes technology is well developed in short IR range (SWIR) while devices operating in mid-wavelength (MWIR) and long-wavelength (LWIR) require cooling to suppress dark current due to the low energy bandgap. The paper presents research on the potential application of the HgCdTe (100) oriented and HgCdTe (111)B heterostructures grown by metal-organic chemical vapor deposition (MOCVD) on GaAs substrates for the design of avalanche photodiodes (APDs) operating in the IR range up to 8 µm and under 2-stage TE cooling (T = 230 K). While HgCdTe band structure with molar composition xCd < 0.5 provides a very favorable hole-to-electron ionization coefficient ratio under avalanche conditions, resulting in increased gain without generating excess noise, the low level of background doping concentration and a low number of defects in the active layer is also required. HgCdTe (100) oriented layers exhibit better crystalline quality than HgCdTe (111)B grown on GaAs substrates, low dislocation density, and reduction of residual defects which contribute to a background doping within the range ~1014 cm–3. The fitting to the experimentally measured dark currents (at T = 230 K) of the N+-ν-p-P+ photodiodes commonly used as an APDs structure allowed to determine the material parameters. Experimentally extracted the mid-bandgap trap concentrations at the level of 2.5 × 1014 cm−3 and 1 × 1015 cm−3 for HgCdTe (100) and HgCdTe (111)B photodiode are reported respectively. HgCdTe (100) is better to provide high resistance, and consequently sufficient strength and uniform electric field distribution, as well as to avoid the tunneling current contribution at higher bias, which is a key issue in the proper operation of avalanche photodiodes. It was presented that HgCdTe (100) based N+-ν-p-P+ gain, M > 100 could be reached for reverse voltage > 5 V and excess noise factor F(M) assumes: 2.25 (active layer, xCd = 0.22, k = 0.04, M = 10) for λcut-off = 8 μm and T = 230 K. In addition the 4-TE cooled, 8 μm APDs performance was compared to the state-of-the-art for SWIR and MWIR APDs based mainly on III-V and HgCdTe materials (T = 77–300 K).

24 February 2023 in Opto-Electronics Review
Verified
Journal Article
Closed access
PDF file
PMPawel Madejczyk
Pawel Madejczyk
WGWaldemar Gawron
Waldemar Gawron
JSJan Sobieski
Jan Sobieski
PMPiotr Martyniuk
Piotr Martyniuk
JRJarosław Rutkowski
Jarosław Rutkowski
This paper presents examples of infrared detectors with mercury cadmium telluride elaborated at the Institute of Applied Physics, Military University of Technology and VIGO Photonics S.A. Fully doped HgCdTe epilayers were grown with the metal organic chemical vapour deposition technique which provides a wide range of material composition covering the entire infrared range from 1.5 µm to 14 µm. Fundamental issues concerning the design of individual areas of the heterostructure including: the absorber, contacts, and transient layers with respect to their thickness, doping and composition were discussed. An example of determining the gain is also given pointing to the potential application of the obtained devices in avalanche photodiode detectors that can amplify weak optical signals. Selected examples of the analysis of current-voltage and spectral characteristics are shown. Multiple detectors based on a connection in series of small individual structures are also presented as a solution to overcome inherent problems of low resistance of LWIR photodiodes. The HgCdTe detectors were compared with detectors from III-V materials. The detectors based on InAs/InAsSb superlattice materials achieve very comparable parameters and, in some respects, they are even superior to those with mercury cadmium telluride.

14 March 2022 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
MKMałgorzata Kopytko
Małgorzata Kopytko
Krzysztof MurawskiKrzysztof Murawski
Krzysztof Murawski
PMPawel Madejczyk
Pawel Madejczyk
JSJan Sobieski
Jan Sobieski
WGWaldemar Gawron
Waldemar Gawron
Mid-wave infrared HgCdTe photodiode grown by metal-organic chemical vapor deposition was characterized for its use in avalanche operation. N + /N/p/P/P + /n + heterostructure meets the assumptions of the separated absorption and multiplication design. The p-type absorber, with an assumed Cd molar composition of 0.305, was optimized to operate up to $4.4 ~\mu \text{m}$ at 230 K. The multiplication region is contained within the N layer with a wider energy gap ( $\text{x}_{\textit {Cd}}=0.33$ ). Satisfactory gain of ~50 was achieved for a moderate reverse bias of −3.5 V and a temperature of 160 K.

1 June 2024 in Sensors
Verified
Journal Article
Open access
PDF file
MKMałgorzata Kopytko
Małgorzata Kopytko
KMKinga Majkowycz
Kinga Majkowycz
Krzysztof MurawskiKrzysztof Murawski
Krzysztof Murawski
JSJan Sobieski
Jan Sobieski
WGWaldemar Gawron
Waldemar Gawron
PMPiotr Martyniuk
Piotr Martyniuk
Deep defects in the long-wave infrared (LWIR) HgCdTe heterostructure photodiode were measured via deep-level transient spectroscopy (DLTS) and photoluminescence (PL). The n+-P+-π-N+ photodiode structure was grown by following the metal–organic chemical vapor deposition (MOCVD) technique on a GaAs substrate. DLTS has revealed two defects: one electron trap with an activation energy value of 252 meV below the conduction band edge, located in the low n-type-doped transient layer at the π-N+ interface, and a second hole trap with an activation energy value of 89 meV above the valence band edge, located in the π absorber. The latter was interpreted as an isolated point defect, most probably associated with mercury vacancies (VHg). Numerical calculations applied to the experimental data showed that this VHg hole trap is the main cause of increased dark currents in the LWIR photodiode. The determined specific parameters of this trap were the capture cross-section for the holes of σp = 10−16–4 × 10−15 cm2 and the trap concentration of NT = 3–4 × 1014 cm−3. PL measurements confirmed that the trap lies approximately 83–89 meV above the valence band edge and its location.

29 April 2024 in Sensors
Verified
Journal Article
Open access
PDF file
JSJan Sobieski
Jan Sobieski
MKMałgorzata Kopytko
Małgorzata Kopytko
KMKacper Matuszelański
Kacper Matuszelański
WGWaldemar Gawron
Waldemar Gawron
JPJózef Piotrowski
Józef Piotrowski
PMPiotr Martyniuk
Piotr Martyniuk
HgCdTe is a well-known material for state-of-the-art infrared photodetectors. The interd-iffused multilayer process (IMP) is used for Metal–Organic Chemical Vapor Deposition (MOCVD) of HgCdTe heterostructures, enabling precise control of composition. In this method, alternating HgTe and CdTe layers are deposited, and they homogenize during growth due to interdiffusion, resulting in a near-uniform material. However, the relatively low (350 °C) IMP MOCVD growth temperature may result in significant residual compositional inhomogeneities. In this work, we have investigated the residual inhomogeneities in the IMP-grown HgCdTe layers and their influence on material properties. Significant IMP growth-related oscillations of composition have been revealed in as-grown epilayers with the use of a high-resolution Secondary Ion Mass Spectroscopy (SIMS). The oscillations can be minimized with post-growth annealing of the layers at a temperature exceeding that of growth. The electric and photoelectric characterizations showed a significant reduction in the background doping and an increase in the recombination time, which resulted in dramatic improvement of the spectral responsivity of photoconductors.