The article presents state of work in technology of free-space optical communications (Free Space Optics − FSO). Both commercially available optical data links and their further development are described. The main elements and operation limiting factors of FSO systems have been identified. Additionally, analyses of FSO/RF hybrid systems application are included. The main aspects of LasBITer project related to such hybrid technology for security and defence applications are presented.
This paper presents the current status of medium-wave infrared (MWIR) detectors at the Military University of Technology’s Institute of Applied Physics and VIGO System S.A. The metal–organic chemical vapor deposition (MOCVD) technique is a very convenient tool for the deposition of HgCdTe epilayers, with a wide range of compositions, used for uncooled infrared detectors. Good compositional and thickness uniformity was achieved on epilayers grown on 2-in-diameter, low-cost (100) GaAs wafers. Most growth was performed on substrates, which were misoriented from (100) by between 2° and 4° in order to minimize growth defects. The large lattice mismatch between GaAs and HgCdTe required the usage of a CdTe buffer layer. The CdTe (111) B buffer layer growth was enforced by suitable nucleation procedure, based on (100) GaAs substrate annealing in a Te-rich atmosphere prior to the buffer deposition. Secondary-ion mass spectrometry (SIMS) showed that ethyl iodide (EI) and tris(dimethylamino)arsenic (TDMAAs) were stable donor and acceptor dopants, respectively. Fully doped (111) HgCdTe heterostructures were grown in order to investigate the devices’ performance in the 3–5 µm infrared band. The uniqueness of the presented technology manifests in a lack of the necessity of time-consuming and troublesome ex situ annealing.
This letter presents InAs $/$ InAsSb-based superlattice (SL) long wavelength (8– $12 \mu \text{m}$ ) range (LWIR) cascade photodetector operating at temperatures > 190 K. The design of the detector resolves the problem of the low quantum efficiency ( QE ) and resistance of the traditional photovoltaic detectors optimized for high temperature (HOT) conditions. The device was deposited by molecular beam epitaxy (MBE) on GaAs substrates with type-II InAs $/$ InAsSb superlattice (T2SLs) absorbers. The constituent stages of the cascade are connected by the low resistance tunnel junctions. Detectivity ( $D^{\ast }$ ) of the unbiased device reaches ~ $6.7\,\,\times10$ 8 cmHz $^{1/2} /\text{W}$ at 210 K, $\lambda $ = $10 \mu \text{m}$ .
Four types of barrier detectors based on a type II InAs/InAsSb superlattice with a wide-gap barrier made of a solid AlInAsSb lattice matched to the GaSb buffer were compared. The tested detectors differed in the type of doping of the active layer and the level and type of doping of the contact layer at the barrier. The epitaxial layers were deposited on GaAs (100) substrates using the molecular beam epitaxy method. The spectral and current–voltage characteristics of the analyzed detectors were compared. The highest current responsivities were observed in the structure with a p-type absorber (p+BpN+). Detectors with an n-type absorber (p+Bnn+, n+Bnn+, and nBnn+) show an increase in the current responsivity with an increase in the reverse bias voltage due to the reduction in the undesirable barrier in the valence band. Arrhenius characteristics for the dark current show that only in nBnn+ detectors, it was possible to limit the generation–recombination current. These detectors at 150 K were characterized by the highest normalized detectivity of approximately 3 × 1011 cm · Hz1/2/W. The obtained results were compared with literature data, showing that the parameters of type II superlattice photodetectors are close to those of HgCdTe photodiodes according to the “Rule 07” and “Rule 22” principles.
The trend related to reach the high operating temperature condition (HOT, temperature, T > 190 K) achieved by thermoelectric (TE) coolers has been observed in infrared (IR) technology recently. That is directly related to the attempts to reduce the IR detector size, weight, and power dissipation (SWaP) conditions. The room temperature avalanche photodiodes technology is well developed in short IR range (SWIR) while devices operating in mid-wavelength (MWIR) and long-wavelength (LWIR) require cooling to suppress dark current due to the low energy bandgap. The paper presents research on the potential application of the HgCdTe (100) oriented and HgCdTe (111)B heterostructures grown by metal-organic chemical vapor deposition (MOCVD) on GaAs substrates for the design of avalanche photodiodes (APDs) operating in the IR range up to 8 µm and under 2-stage TE cooling (T = 230 K). While HgCdTe band structure with molar composition xCd < 0.5 provides a very favorable hole-to-electron ionization coefficient ratio under avalanche conditions, resulting in increased gain without generating excess noise, the low level of background doping concentration and a low number of defects in the active layer is also required. HgCdTe (100) oriented layers exhibit better crystalline quality than HgCdTe (111)B grown on GaAs substrates, low dislocation density, and reduction of residual defects which contribute to a background doping within the range ~1014 cm–3. The fitting to the experimentally measured dark currents (at T = 230 K) of the N+-ν-p-P+ photodiodes commonly used as an APDs structure allowed to determine the material parameters. Experimentally extracted the mid-bandgap trap concentrations at the level of 2.5 × 1014 cm−3 and 1 × 1015 cm−3 for HgCdTe (100) and HgCdTe (111)B photodiode are reported respectively. HgCdTe (100) is better to provide high resistance, and consequently sufficient strength and uniform electric field distribution, as well as to avoid the tunneling current contribution at higher bias, which is a key issue in the proper operation of avalanche photodiodes. It was presented that HgCdTe (100) based N+-ν-p-P+ gain, M > 100 could be reached for reverse voltage > 5 V and excess noise factor F(M) assumes: 2.25 (active layer, xCd = 0.22, k = 0.04, M = 10) for λcut-off = 8 μm and T = 230 K. In addition the 4-TE cooled, 8 μm APDs performance was compared to the state-of-the-art for SWIR and MWIR APDs based mainly on III-V and HgCdTe materials (T = 77–300 K).