Yingjie Cai

Prof. Dr. Yingjie Cai

Hubei Provincial Engineering Laboratory for Clean Production and High Value Utilization of Bio-Based Textile Materials, Wuhan Textile University, Wuhan 430200, China
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2023 in Membranes
Verified
Journal Article
Open access
PDF file
TRTanzim Ur Rahman
Tanzim Ur Rahman
HRHridoy Roy
Hridoy Roy
RIReazul Islam
Reazul Islam
MTMohammed Tahmid
Mohammed Tahmid
AFAthkia Fariha
Athkia Fariha
Md Shahinoor IslamMd Shahinoor Islam
Md Shahinoor Islam
The advancement in water treatment technology has revolutionized the progress of membrane bioreactor (MBR) technology in the modern era. The large space requirement, low efficiency, and high cost of the traditional activated sludge process have given the necessary space for the MBR system to come into action. The conventional activated sludge (CAS) process and tertiary filtration can be replaced by immersed and side-stream MBR. This article outlines the historical advancement of the MBR process in the treatment of industrial and municipal wastewaters. The structural features and design parameters of MBR, e.g., membrane surface properties, permeate flux, retention time, pH, alkalinity, temperature, cleaning frequency, etc., highly influence the efficiency of the MBR process. The submerged MBR can handle lower permeate flux (requires less power), whereas the side-stream MBR can handle higher permeate flux (requires more power). However, MBR has some operational issues with conventional water treatment technologies. The quality of sludge, equipment requirements, and fouling are major drawbacks of the MBR process. This review paper also deals with the approach to address these constraints. However, given the energy limitations, climatic changes, and resource depletion, conventional wastewater treatment systems face significant obstacles. When compared with CAS, MBR has better permeate quality, simpler operational management, and a reduced footprint requirement. Thus, for sustainable water treatment, MBR can be an efficient tool.

30 April 2023 in Membranes
Verified
Journal Article
Open access
PDF file
HRHridoy Roy
Hridoy Roy
TRTanzim Ur Rahman
Tanzim Ur Rahman
NTNishat Tasnim
Nishat Tasnim
JAJannatul Arju
Jannatul Arju
MRMd. Mustafa Rafid
Md. Mustafa Rafid
Md Shahinoor IslamMd Shahinoor Islam
Md Shahinoor Islam
A microbial fuel cell (MFC) is a system that can generate electricity by harnessing microorganisms’ metabolic activity. MFCs can be used in wastewater treatment plants since they can convert the organic matter in wastewater into electricity while also removing pollutants. The microorganisms in the anode electrode oxidize the organic matter, breaking down pollutants and generating electrons that flow through an electrical circuit to the cathode compartment. This process also generates clean water as a byproduct, which can be reused or released back into the environment. MFCs offer a more energy-efficient alternative to traditional wastewater treatment plants, as they can generate electricity from the organic matter in wastewater, offsetting the energy needs of the treatment plants. The energy requirements of conventional wastewater treatment plants can add to the overall cost of the treatment process and contribute to greenhouse gas emissions. MFCs in wastewater treatment plants can increase sustainability in wastewater treatment processes by increasing energy efficiency and reducing operational cost and greenhouse gas emissions. However, the build-up to the commercial-scale still needs a lot of study, as MFC research is still in its early stages. This study thoroughly describes the principles underlying MFCs, including their fundamental structure and types, construction materials and membrane, working mechanism, and significant process elements influencing their effectiveness in the workplace. The application of this technology in sustainable wastewater treatment, as well as the challenges involved in its widespread adoption, are discussed in this study.

19 November 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
NJNusrat Jahan
Nusrat Jahan
MTMohammed Tahmid
Mohammed Tahmid
ASAfrina Zaman Shoronika
Afrina Zaman Shoronika
AFAthkia Fariha
Athkia Fariha
HRHridoy Roy
Hridoy Roy
Md Shahinoor IslamMd Shahinoor Islam
Md Shahinoor Islam
Clothing, one of the basic needs, demands the growth of textile industries worldwide, resulting in higher consumption and pollution of water. Consequently, it requires extensive treatment of textile effluent for environmental protection as well as reuse purposes. Primary treatment, secondary treatment, and tertiary treatment are the three major phases of textile wastewater treatment. Secondary treatment under aerobic and anaerobic circumstances is carried out to decrease BOD, COD, phenol, residual oil, and color, whereas primary treatment is utilized to remove suspended particles, oil, grease, and gritty materials. However, biological treatment is not fully capable of treating water according to discharge/reuse standards. Hence, tertiary treatment is used to remove final contaminants from the wastewater. Adsorption is regarded as one of the most feasible processes for dye and metal removal in consideration of cost and variation in the adsorbent. Though membrane filtration is an efficient process, the cost of operation limits its application. It’s unfortunate that there isn’t a universally applicable treatment solution for textile effluents. Therefore, the only flexible strategy is to combine several therapy modalities. Treatment of complicated, high-strength textile wastewater depending on pollutant load will be more successful if physical, chemical, and biological approaches are used in tandem. Enforcement of stringent environmental regulation policies, increasing costs and demand for freshwater, and the rising costs and difficulties associated with wastewater disposal are accelerating efforts toward achieving ZLD. Additionally, research into methods for extracting useful materials from wastewater has blossomed in recent years. As such, the purpose of this analysis is to give a holistic overview of textile wastewater treatment systems, with a focus on zero liquid discharge (ZLD) and efficient resource recovery, both of which may hasten the transition to more sustainable water management.

5 November 2020 in npj Clean Water
Verified
Journal Article
Open access
PDF file
MPMd. Nahid Pervez
Md. Nahid Pervez
MBMalini Balakrishnan
Malini Balakrishnan
SHShadi Wajih Hasan
Shadi Wajih Hasan
Kwang-Ho ChooKwang-Ho Choo
Kwang-Ho Choo
YZYaping Zhao
Yaping Zhao
Vincenzo NaddeoVincenzo Naddeo
Vincenzo Naddeo
The concept of nanomaterials membranes (NMs) promises to be a sustainable route to improve the membrane characteristics and enhance the performance of membrane bioreactors (MBRs) treating wastewater. This paper provided a critical review of recent studies on the use of membranes incorporating nanomaterials in membrane bioreactor (NMs-MBR) applications for wastewater treatment. Novel types of nanomaterials membranes were identified and discussed based on their structural morphologies. For each type, their design and fabrication, advances and potentialities were presented. The performance of NMs-MBR system has been summarized in terms of removal efficiencies of common pollutants and membrane fouling. The review also highlighted the sustainability and cost viability aspects of NMs-MBR technology that can enhance their widespread use in wastewater treatment applications.

15 June 2023 in Scientific Reports
Verified
Journal Article
Open access
PDF file
NPNahid Pervez
Nahid Pervez
WYWan Sieng Yeo
Wan Sieng Yeo
MMMst. Monira Rahman Mishu
Mst. Monira Rahman Mishu
ETEman Talukder
Eman Talukder
HRHridoy Roy
Hridoy Roy
Vincenzo NaddeoVincenzo Naddeo
Vincenzo Naddeo
Despite the widespread interest in electrospinning technology, very few simulation studies have been conducted. Thus, the current research produced a system for providing a sustainable and effective electrospinning process by combining the design of experiments with machine learning prediction models. Specifically, in order to estimate the diameter of the electrospun nanofiber membrane, we developed a locally weighted kernel partial least squares regression (LW-KPLSR) model based on a response surface methodology (RSM). The accuracy of the model's predictions was evaluated based on its root mean square error (RMSE), its mean absolute error (MAE), and its coefficient of determination (R2). In addition to principal component regression (PCR), locally weighted partial least squares regression (LW-PLSR), partial least square regression (PLSR), and least square support vector regression model (LSSVR), some of the other types of regression models used to verify and compare the results were fuzzy modelling and least square support vector regression model (LSSVR). According to the results of our research, the LW-KPLSR model performed far better than other competing models when attempting to forecast the membrane's diameter. This is made clear by the much lowerRMSEandMAEvalues of the LW-KPLSR model. In addition, it offered the highest R2values that could be achieved, reaching 0.9989.

15 March 2018 in Materials
Verified
Journal Article
Open access
PDF file
MPMd. Nahid Pervez
Md. Nahid Pervez
FSFAIZAN SHAFIQ
FAIZAN SHAFIQ
ZSZahid Sarwar
Zahid Sarwar
MJMuhammad Munib Jilani
Muhammad Munib Jilani
Yingjie CaiYingjie Cai
Yingjie Cai
In this study, the influence and optimization of the factors of a non-formaldehyde resin finishing process on cotton fabric using a Taguchi-based grey relational analysis were experimentally investigated. An L27 orthogonal array was selected for five parameters and three levels by applying Taguchi’s design of experiments. The Taguchi technique was coupled with a grey relational analysis to obtain a grey relational grade for evaluating multiple responses, i.e., crease recovery angle (CRA), tearing strength (TE), and whiteness index (WI). The optimum parameters (values) for resin finishing were the resin concentration (80 g·L−1), the polyethylene softener (40 g·L−1), the catalyst (25 g·L−1), the curing temperature (140 °C), and the curing time (2 min). The goodness-of-fit of the data was validated by an analysis of variance (ANOVA). The optimized sample was characterized by Fourier-transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and scanning electron microscope (SEM) to better understand the structural details of the resin finishing process. The results showed an improved thermal stability and confirmed the presence of well deposited of resin on the optimized fabric surface.