A two-electrode graphite gas switch has been widely used in power conditioning systems for high-power laser pumping due to its simple structure, robustness, and low cost. Previous studies have shown that the lifetime of the graphite gas switches mainly depended on the graphite erosion performance, while different types of graphite materials displayed a great difference in erosion performance. In order to understand the erosion mechanism of the graphite electrodes under high-current, high-Coulomb transfer working conditions, the electrode's surface morphology was obtained during the lifetime experiments, and the thermophysical process on the electrode surface was studied. The results showed that the energy derived from arc plasma was mainly used for graphite sublimation, and the surface morphology of the graphite electrodes was obviously different. The reason could be that the heat flux on anode and cathode surfaces was different due to convection process generated by electron flow during discharge. The erosion rate of the anode was heavier than that of the cathode, and the proportion was around 2.15:1. The measured erosion rates of the electrodes were linearly increased with the number of discharges; this was significant for predicting the lifetime of the two-electrode graphite gas switch.
The breakdown characteristics of a trigatron spark gap triggered by a plasma jet are studied in this paper; the development of a plasma jet and the influence of the gap distance, working coefficient, and plasma jet ejection properties on breakdown characteristics are compared. The results show that the plasma jet ejecting process can be divided into expanding, steady, and dissipating phases. The electric field distortion induced by the plasma jet is different during the expanding and dissipating phase, in which the plasma jet length increases and the radius of the curvature of the plasma jet front decreases, respectively. As the two processes have different variation rates, a faster increasing rate of the breakdown delay can be obtained during the dissipating phase. A detailed physical mode that explains the effects on the triggered breakdown process is presented. The shape of a plasma jet induced by polyethylene and ceramic surface discharge changes to a great extent during the dissipating phase; a more stable plasma jet can be obtained when induced only by polyethylene, resulting in a smaller breakdown delay under a low working coefficient. The ultraviolet radiation (UV) generated by the plasma jet is effective in reducing the critical breakdown electric field, while the electric field distortion induced by the plasma jet is the main reason behind the triggered breakdown under different working coefficients; the UV could play a limited role in the triggered breakdown process.
1 December 2024 in Review of Scientific Instruments
The high-strain rate mechanical behavior of aluminum alloys is crucial for the stability of electromagnetic launch systems. However, current high-strain rate testing methods are not suitable for large-scale screening of materials needed in electromagnetic launch systems due to their low precision and high cost. In this paper, a novel method for high-strain rate tensile testing of aluminum alloys based on magnetic pulse driving was proposed. The method can generate a fast-rising edge and adjustable stress pulses to enable uniaxial tensile deformation, reaching a target strain rate quickly and keeping it constant. Based on the theory of stress wave transmission, a single-point method for measuring stress–strain relationship of the specimen combining digital image correlation (DIC) technology is proposed. Finite element simulations using the explicit finite element software LS-DYNA demonstrate a good agreement between the strains and strain rate with experimental values. Tensile tests were conducted on AA7075 in the strain rate range of 1000–3000 s−1, the stress–strain relationship obtained from DIC agrees well with the results of traditional Hopkinson bar experiments.
1 December 2020 in Review of Scientific Instruments
This paper presents the design and test of a gas-insulated linear transformer driver (LTD) cavity aimed at the Z-pinch experimental device CZ-34. The LTD cavity has a diameter of 2290 mm and a height of 346 mm. It consists of 23 main bricks and 1 trigger brick. Each main brick is comprised of two 100 nF capacitors connected electrically in series with a field-distortion gas switch. The trigger brick is comprised of two 50 nF capacitors connected in series with a compact multi-gap gas switch. All bricks are placed in the cavity filled with compressed SF6 and are pluggable like drawers. The trigger pulse generated by the trigger brick passes through an azimuthal transmission line to the trigger ring and makes the main bricks discharge synchronously. The LTD cavity can deliver ∼1 MA current pulse with a rise time of 115 ns to 0.08 Ω liquid resistance load when the charging voltage is ±100 kV, which is in good agreement with the circuit simulation results. Experimental results demonstrate the successful application of using gas insulation and pluggable bricks. The technical feasibility of the charging configuration, triggering method, and isolation resistors is verified. There is little difference in output performance as return-current rods replaced the outside metal cylinder, which provides a new path for the design of LTD cavities in series.
This paper presents experimental results on a trigatron spark gap breakdown process induced by different densities of the injected plasma. The results show that the shape of the injected plasma has a great influence on the electric field distribution. The decrease in the curvature radius of the injected plasma front can induce a breakdown during the dissipation of the injected plasma. This process is significant in explaining the sharp increase in the breakdown delay and jitter observed under very low working coefficients. The inception and propagation of the streamer are studied in detail. Due to the high intensity illumination, direct ionization between the injected plasma front and the head of the streamer can occur during the propagation of the streamer. This differs from the conventional streamer breakdown process under a uniform electric field. An explanation of the streamer inception and the direct ionization between the front of the injected plasma and the streamer head is presented. Using the Meek criterion, the effects of electric field distortion and photoionization induced by the injected plasma are analyzed. The results indicate that the effect of the photoionization changes significantly with the density and duration of the plasma injection. Combining this effect with the electric field distortion, a breakdown can occur under a very low working coefficient.
14 October 2019 in IEEE Transactions on Nanotechnology
Nano-aluminum particles are fabricated by the electrical explosion of wires (EEW) in argon atmosphere. The characteristics of the current, voltage, and the deposited energy of exploding Al wire with and without the shunting gap are studied. In order to understand the influence of the partial reheating process on the production of nanoparticles, the shadowgraphs are used to study the expansion process of the exploding Al with and without the shunting gap, it is observed that the expansion rates of exploding Al without the shunting gap have two peaks, while the expansion rates of exploding Al with the shunting gap have only one peak. The size and shape of the nanoparticles are analyzed using scanning electron microscopy (SEM) analysis. It is found that almost all the nanoparticles are basically spherical in shape, and the average particle size under different experimental conditions are obtained using SEM. The study of the partial reheating process suggests that the partial reheating process can reduce the average size of the nanoparticles.