WO3-treated fullerene/TiO2 composites (WO3-fullerene/TiO2) were prepared using a sol-gel method. The composite obtained was characterized by BET surface area measurements, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, transmission electron microscopy, and UV-vis analysis. A methyl orange (MO) solution under visible light irradiation was used to determine the photocatalytic activity. Excellent photocatalytic degradation of a MO solution was observed using the WO3-fullerene, fullerene-TiO2, and WO3-fullerene/TiO2 composites under visible light. An increase in photocatalytic activity was observed, and WO3-fullerene/TiO2 has the best photocatalytic activity; it may attribute to the increase of the photo-absorption effect by the fullerene and the cooperative effect of the WO3.
CdSe, CdSe-TiO2, and CdSe-C60/TiO2 composites were prepared using sol–gel method, and their photocatalytic activity was evaluated by measuring the degradation of rhodamine B solutions under visible light. The surface area, surface structure, crystal phase, and elemental identification of these composites were characterized by nitrogen adsorption isotherms, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), and UV-visible (vis) absorption spectrophotometry. XRD showed that the CdSe-C60/TiO2 composite contained a typical single and clear anatase phase. SEM of the CdSe-C60/TiO2 composites revealed a homogenous composition in the particles. EDX revealed the presence of C and Ti with strong Cd and Se peaks in the CdSe-C60/TiO2 composite. The degradation of dye was determined by UV–vis spectrophotometry. An increase in photocatalytic activity was observed and attributed to an increase in the photoabsorption effect by fullerene and the cooperative effect of the CdSe. The repeatability of photocatalytic activity was also tested in order to investigate the stability of C60 and CdS-C60/TiO2 composites.
Developing photocatalysts with molecular recognition function is very interesting and desired for specific applications in the environmental field. Copper ferrite/N-doped graphene (CuFe2O4/NG) hybrid catalyst was synthesized and characterized by surface photovoltage spectroscopy, X-ray powder diffraction, transmission electron microscopy, Raman spectroscopy, UV–Vis near-infrared diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy. The CuFe2O4/NG catalyst can recognize ammonia from rhodamine B (RhB) in ammonia-RhB mixed solution and selectively degrade ammonia under visible near-infrared irradiation. The degradation ratio for ammonia reached 92.6% at 6 h while the degradation ratio for RhB was only 39.3% in a mixed solution containing 100.0 mg/L NH3-N and 50 mg/L RhB. Raman spectra and X-ray photoelectron spectra indicated ammonia adsorbed on CuFe2O4 while RhB was adsorbed on NG. The products of oxidized ammonia were detected by gas chromatography, and results showed that N2 was formed during photocatalytic oxidization. Mechanism studies showed that photo-generated electrons flow to N-doped graphene following the Z-scheme configuration to reduce O2 dissolved in solution, while photo-generated holes oxidize directly ammonia to nitrogen gas.
The catalyst materials 0N-Cu-MOF, 1N-Cu-MOF, and 2N-Cu-MOF were successfully synthesized usinga solvothermal method, and using different concentrations of nitrogen-modified Cu organic frameworks (xN-Cu-MOF). Characterizations using X-ray diffraction (XRD), scanning electron microscopy (SEM), fourier transform infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS), and Brunauer-Emmett-Teller (BET) surface area analysis showed that 1N-Cu-MOF had the largest SSA and pore size among the three materials synthesized. 1N-Cu-MOF exhibited the largest pore size and specific surface area among the three materials, which had a decisive effect on CO 2 reduction. In addition, stability and CO 2 reduction reaction (CO 2 RR) activity were evaluated by linear sweep voltmeter, cyclic voltmeter, electrochemical impedance spectroscopy, and time flow tests. Faradaic efficiency (FE) was determined by product analysis. Among the three catalyst materials, 1N-Cu-MOF showed the best catalytic performance at 50 mA・cm-2 (maximum current density). The charge transfer resistance was 8.23 Ω, the average current density was 19.9 mA・cm-2 , and the FE of methane (CH 4) production showed a high efficiency of 70.45 % when tested for 12 h at an overpotential of-0.35 V (to-RHE).