Waqas Javid

Mr. Waqas Javid

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2024 in Materials Proceedings
Verified
Conference Paper
Open access
PDF file
AWAbdul Wahab
Abdul Wahab
WJWaqas Javid
Waqas Javid
HAHamza Ahmed
Hamza Ahmed
ASAbdullah Sheikh
Abdullah Sheikh
MSMuhammad Shahbaz
Muhammad Shahbaz
SIShahid Iqbal
Shahid Iqbal
This study presents a solar-powered parabolic dish desalination system with a solar tracking system and conical receiver. It efficiently transforms solar radiation into heat and evaporates saltwater, producing fresh water. The system is sustainable and affordable, making it a viable solution for water desalination in areas with limited access to fresh water. It achieves a high conversion rate from saltwater to fresh water, while consuming minimal energy. The results indicate that the system effectively utilizes solar energy, exhibiting high efficiency levels ranging from 78.56% to 82.77%, with an average efficiency of 80.79%. This system offers an effective solution to meet the growing demand for fresh water in water-scarce regions.

15 April 2024 in Materials Proceedings
Verified
Conference Paper
Open access
PDF file
SZSyed Azfar Imam Zaidi
Syed Azfar Imam Zaidi
SIShahid Iqbal
Shahid Iqbal
FHFahad Hussain
Fahad Hussain
MIMuhammad Hammad Ikram
Muhammad Hammad Ikram
WJWaqas Javid
Waqas Javid
MMMuhammad Mateen
Muhammad Mateen
Energy is the primary concern of the modern era and the requirement of energy is being increased day by day; energy resources are not sufficiently available for sustainable development. It is crucial to generate affordable and pollution-free sources of energy to meet this required demand. Walking is a common daily activity for humans; the kinetic energy from walking is converted into mechanical energy. Moreover, this energy is converted into electrical power using a rack-and-pinion mechanism which is simply a non-conventional method of producing electric current. In this research study, a simple and low-cost rack-and-pinion mechanism with a flywheel is introduced to enhance the performance and efficiency of energy conversion from kinetic energy to mechanical energy and subsequently into electrical energy. The results showed that the proposed footstep floor tile generated an average power of 3 watts for a 0.5 s duration with a peak load of 60 kg. The electrical energy produced per step was noted as 1.8 Joules. A percentage of 75% of the total potential energy theoretically accessible was transmitted by the energy-harvesting paver, and 50% of it was successfully converted into electricity. The generated energy is stored in a backup battery bank system and can be used to charge smart devices, providing a cost-effective and pollution-free solution.

25 March 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
WJWaqas Javid
Waqas Javid
PKProf. Dr. Shahab Khushnood
Prof. Dr. Shahab Khushnood
LNLuqman Ahmad Nizam
Luqman Ahmad Nizam
MNMuhammad Atif Niaz
Muhammad Atif Niaz
SIShahid Iqbal
Shahid Iqbal
Finned tubes contribute to the heat transfer performance of heat exchangers by increasing the surface area; they also modify patterns within the flow around the tubes and thus increase the likelihood of flow-induced vibrations (FIVs), which can undermine structural integrity. The tradeoff between improved heat transfer and minimized vibration risks is thus of concern in the optimization of finned tube designs. This paper examines the vibration behavior of circular finned tubes fitted in a parallel triangular configuration when subjected to crossflow conditions with particular reference to the structural response as opposed to thermal performance. In this study, two tube bundles arranged in a 30° parallel triangular layout were tested. The test tube has pitch-to-diameter (P/D) ratios of 1.16 and 1.37 and fin densities of 3, 6, and 9. In this study, experiments were conducted in a low-speed closed-loop water tunnel, which also involved the fabrication of circular finned tubes, the preparation of test bundles, and vibration response measurements. The key parameters analyzed in this experiment were the vibration amplitude, damping, pitch ratio, and fin density. Based on the free-stream velocity range of 0.13–0.28 m/s in a 300 mm × 300 mm closed-circuit water tunnel (hydraulic diameter Dh=0.3 m), the Reynolds number ranged from 3.9 × 104 to 8.4 × 104 (water at 20 °C). The results of this experiment demonstrate that by increasing the fin density, the vibration amplitudes can be reduced, which also raises the critical velocities. Reducing the pitch ratio from 1.37 to 1.16 produced an onset of instability approximately 53% earlier than the onset of instability at the ratio of 1.37. The bandwidth of the pitch ratio of 1.16 at the same fin density of 9 was almost 45% lower than that at 1.37, which confirms that the system at 1.16 is much more unstable. In general, the 1.37 pitch ratio offers 3 times higher stability margins than those of 1.16 for the fin densities under study. The development of optimal finned tube heat exchanger designs that reduce flow-induced vibrations without sacrificing thermal performance is aided by these findings, which provide information on the relationship between the fin density, pitch ratio and vibration behavior.

6 May 2024 in Materials Proceedings
Verified
Conference Paper
Open access
PDF file
UZusman zafar
usman zafar
WJWaqas Javid
Waqas Javid
FJFurqan Jamil
Furqan Jamil
SIShahid Iqbal
Shahid Iqbal
SASikander Ahmed
Sikander Ahmed
TMTayyab Mehmood
Tayyab Mehmood
The demand for energy is gradually increasing; governments are looking for affordable and long-lasting solutions. Hydropower is crucial for addressing this issue. Low-head hydropower stations are necessary in certain regions due to their geographical position. Gravitational water vortex turbines are an alternative for these low-head turbines. They use the water’s tangential flow to create a vortex, converting mechanical energy to kinetic energy. The design of turbine blades and basins using SolidWorks and CFD analysis was carried out during this research. CFD investigation showed that the conical basin had a higher exit velocity than the cylindrical basin, indicating a successful design.

8 September 2023 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
URUbaid ur Rehman
Ubaid ur Rehman
MAMuhammad Ashiq
Muhammad Ashiq
MRMuhammad Ahmad Rafi
Muhammad Ahmad Rafi
UMUsama Malik
Usama Malik
WJWaqas Javid
Waqas Javid
MAMehmood Ul Hassan Amjad
Mehmood Ul Hassan Amjad
In Pakistan, residential energy consumption is predominantly devoted to ensuring thermal comfort, making energy reduction a significant task in building load management. Windows, which are notorious for having poor thermal barriers, contribute considerably to energy losses under harsh weather conditions. Incorporating high thermal inertia materials in windows, such as transparent insulation materials (TIM) and phase change materials (PCM), offers the potential for energy reduction. Using numerical simulations in ANSYS Fluent, this study compares three window types and explores their influence on interior temperature. The findings show that PCM-based windows have a low temperature increase during the melting phase, indicating their great energy-saving potential. Furthermore, PCM absorbs almost 90% of exposed heat, emphasizing its usefulness for energy saving in the Pakistani building industry.