Tube bundles of shell and tube-type heat exchangers often fail because of vibrations produced in tubes due to flow. The turbulence in the flow is the primary cause of vibrations in the tubes. In this study, a tube positioned in the third row of the tube bundle was considered to determine the...
This research work experimentally investigates the effectiveness of various adhesives in bonding Kevlar fiber-reinforced polymer with aluminum alloy 6061-T6 in a hybrid double-strap joint. Hybrid double-strap joints were developed using thermosetting epoxy Araldite LY5052 with Aradur H5052 and thermoplastic epoxy polyurethane mixed with tetrahydrofuran. These specimens were prepared using a hand layup method. Both adhesives were used to make eighty samples: forty for thermoplastic epoxy polyurethane with tetrahydrofuran and forty for thermosetting epoxy Araldite LY5052 with Aradur H5052. In order to determine the static strength of joints, tensile tests were conducted using a universal testing machine (UTM) where a tension–tension fatigue test was carried out on 50%, 70%, and 80% of the static load at which the joint failed. In the thermosetting double lap strap joint, the findings of both the elongation and fatigue tests showed an increase in strength throughout both the elongation and fatigue cycles. Thermosetting Kevlar hybrid joints have a high static and fatigue strength. Based on the results, thermosetting hybrid joints using Aradur H5052 and epoxy Araldite LY5052 had a static strength of 20.67 KN, whereas a thermoplastic adhesive joint had a static strength of 11.93 KN. Furthermore, the microscopic failure modes revealed that the mode of failure for the joints was cohesive and mixed-mode failure.
Finned tubes contribute to the heat transfer performance of heat exchangers by increasing the surface area; they also modify patterns within the flow around the tubes and thus increase the likelihood of flow-induced vibrations (FIVs), which can undermine structural integrity. The tradeoff between improved heat transfer and minimized vibration risks is thus of concern in the optimization of finned tube designs. This paper examines the vibration behavior of circular finned tubes fitted in a parallel triangular configuration when subjected to crossflow conditions with particular reference to the structural response as opposed to thermal performance. In this study, two tube bundles arranged in a 30° parallel triangular layout were tested. The test tube has pitch-to-diameter (P/D) ratios of 1.16 and 1.37 and fin densities of 3, 6, and 9. In this study, experiments were conducted in a low-speed closed-loop water tunnel, which also involved the fabrication of circular finned tubes, the preparation of test bundles, and vibration response measurements. The key parameters analyzed in this experiment were the vibration amplitude, damping, pitch ratio, and fin density. Based on the free-stream velocity range of 0.13–0.28 m/s in a 300 mm × 300 mm closed-circuit water tunnel (hydraulic diameter m), the Reynolds number ranged from 3.9 × 104 to 8.4 × 104 (water at 20 °C). The results of this experiment demonstrate that by increasing the fin density, the vibration amplitudes can be reduced, which also raises the critical velocities. Reducing the pitch ratio from 1.37 to 1.16 produced an onset of instability approximately 53% earlier than the onset of instability at the ratio of 1.37. The bandwidth of the pitch ratio of 1.16 at the same fin density of 9 was almost 45% lower than that at 1.37, which confirms that the system at 1.16 is much more unstable. In general, the 1.37 pitch ratio offers 3 times higher stability margins than those of 1.16 for the fin densities under study. The development of optimal finned tube heat exchanger designs that reduce flow-induced vibrations without sacrificing thermal performance is aided by these findings, which provide information on the relationship between the fin density, pitch ratio and vibration behavior.
The intensifying global energy demand necessitates a transition toward sustainable energy systems, amplifying the need for effective Energy Management System (EMS) software tools for planning, simulation, and decision-making. Existing studies largely offer descriptive comparisons of EMS tools, with limited attention to the relationships among their key characteristics. This study addresses that gap through a data-driven, user-centered evaluation framework. It assesses the perceived importance and interdependencies of eleven key dimensions of EMS software tools, based on a cross-sectional survey of 75 respondents with relevant academic and professional experience. Data were analyzed using descriptive statistics, Pearson correlation, and Exploratory Factor Analysis (EFA). Economic Analysis Capability, Real-World Application, and Computational Capacity emerged as the most critical dimensions, with strong Bonferroni-corrected associations among computational performance, usability, and practical applicability. EFA identified three latent dimensions comprising of performance and usability integration, technical and analytical capability, and system configuration flexibility explaining 72% of total variance. The findings suggest that EMS tools perceived as effective require a balanced integration of computational strength, usability, economic evaluation, and real-world applicability. By moving beyond descriptive comparisons toward a statistically grounded, relational evaluation framework, this study offers practical insights for EMS tool selection and future development for sustainable energy applications.
28 December 2023 in University of Wah Journal of Science and Technology (UWJST)
The popularity of biofuel is increasing rapidly due to scarcity of petroleum fuel and its equitableness towards the environment issues. Mostly biodiesel is produced with transesterification, in which organic oils or analogous stuff is reacted with alcohol in the presence of a suitable catalyst.In this study Methanol and Sodium Hydroxide (NaOH), as catalyst, was used to transesterify the Jatropha Oil. Since the economic sustainability is very important, so the study was made to cut down the cost of production of biodiesel. As the cost of Methanol and NaOH is considerable, so the amount of methanol and Sodium Hydroxide was optimized. The amount of methanol varied from 10% to 30% and NaOH varied from 8% to 20%. It was found that 21% methanol and 10.5% NaOH (m/v) revealed the highest yield i.e.96%, when Jatropha oil was used as feedstock. Mathematical model was developed and theoretical results were compared with experimental results. Both models were superimposed and a comprehensive correlation was established.