Shell and tube heat exchangers (H.Xs) are being used broadly in the generation of power, refrigeration, nuclear, chemical, and petroleum industries due to their high cooling and heating capacity. In this research paper, an experimental test bench for a shell and tube H.X was fabricated according to the standard. This study aimed to test the thermal performance of shell and tube H.Xs using Al2O3-γ nanofluid with different concentrations in counter flow configurations. Nanoparticles of 12 nm of size and 99% purity were used in this investigation. These nanoparticles were dispersed in distilled water to prepare nanofluids at three different concentrations: 0.11%, 0.22%, and 0.34%. Nanofluids of different concentrations were heated and passed through H.X tubes while water was passed through the shell side. The experiments were performed at three different flow rates: 6, 8, and 10 L per minute (L/min). It was observed from the experimentation that nanofluid has higher efficiency as compared to simple distilled water. Experimental investigations showed higher values of overall heat transfer coefficient (U), convective heat transfer coefficient (h), and heat transfer rate () at 0.22%, noted as 33.33%, 48%, and 30%, respectively. The lowest value for U was noted 47% for distilled water. The hydrodynamic and thermal boundary layers were also determined, and when the flow rate increased it led to thinning of the thermal boundary layer and improved heat transfer; however, increased concentrations of nanoparticles thickened the boundary layer by increasing viscosity and boosting thermal conductivity (k) simultaneously. It was revealed that the best concentration for maximizing heat transfer was 0.22%. The findings show that heat transmission efficiency was improved at both 0.11% and 0.22% of nanofluids compared to simple distilled water; when the concentration was raised to 0.34%, the results decreased due to increasing viscosity. Therefore, there is a need to precisely adjust the nanoparticle loading rate for maximum heat transfer enhancement without affecting fluid properties.
This study presents a solar-powered parabolic dish desalination system with a solar tracking system and conical receiver. It efficiently transforms solar radiation into heat and evaporates saltwater, producing fresh water. The system is sustainable and affordable, making it a viable solution for water desalination in areas with limited access to fresh water. It achieves a high conversion rate from saltwater to fresh water, while consuming minimal energy. The results indicate that the system effectively utilizes solar energy, exhibiting high efficiency levels ranging from 78.56% to 82.77%, with an average efficiency of 80.79%. This system offers an effective solution to meet the growing demand for fresh water in water-scarce regions.
Energy is the primary concern of the modern era and the requirement of energy is being increased day by day; energy resources are not sufficiently available for sustainable development. It is crucial to generate affordable and pollution-free sources of energy to meet this required demand. Walking is a common daily activity for humans; the kinetic energy from walking is converted into mechanical energy. Moreover, this energy is converted into electrical power using a rack-and-pinion mechanism which is simply a non-conventional method of producing electric current. In this research study, a simple and low-cost rack-and-pinion mechanism with a flywheel is introduced to enhance the performance and efficiency of energy conversion from kinetic energy to mechanical energy and subsequently into electrical energy. The results showed that the proposed footstep floor tile generated an average power of 3 watts for a 0.5 s duration with a peak load of 60 kg. The electrical energy produced per step was noted as 1.8 Joules. A percentage of 75% of the total potential energy theoretically accessible was transmitted by the energy-harvesting paver, and 50% of it was successfully converted into electricity. The generated energy is stored in a backup battery bank system and can be used to charge smart devices, providing a cost-effective and pollution-free solution.
In this research, the effect of change in stacking sequences on the impact performance of bio-hybrid fiber-reinforced polymer (bio-HFRP) composite materials was analyzed and evaluated. The methodology was developed, based on the mechanical testing and utilization of tree-based machine learning regression models. Low-velocity impact (LVI) testing was performed on five distinct stacking sequences of carbon/flax bio-HFRP at energies ranging from 15 J to 90 J. For all tests, peak impact force was recorded and compared. Symmetric configurations with a uniform distribution of flax layers across the composite laminate exhibited better impact performance. Additionally, two tree-based machine learning (ML) algorithms were used: random forest (RF) and decision tree (DT). The performance metrics used to assess and compare the efficiency were the coefficient of determination (R2), mean square error (MSE), and mean absolute error (MAE). The most accurate model for the prediction of peak impact force was DT with the R2 training and test dataset values of 0.9920 and 0.9045, respectively. Furthermore, lower MSE and MAE values were attained using the DT model as compared to the RF model. The developed methodology and the model serve as powerful tools to predict the damage-induced properties of bio-HFRP composite laminates utilizing minimal resources and saving time as well.
The demand for energy is gradually increasing; governments are looking for affordable and long-lasting solutions. Hydropower is crucial for addressing this issue. Low-head hydropower stations are necessary in certain regions due to their geographical position. Gravitational water vortex turbines are an alternative for these low-head turbines. They use the water’s tangential flow to create a vortex, converting mechanical energy to kinetic energy. The design of turbine blades and basins using SolidWorks and CFD analysis was carried out during this research. CFD investigation showed that the conical basin had a higher exit velocity than the cylindrical basin, indicating a successful design.
This research work experimentally investigates the effectiveness of various adhesives in bonding Kevlar fiber-reinforced polymer with aluminum alloy 6061-T6 in a hybrid double-strap joint. Hybrid double-strap joints were developed using thermosetting epoxy Araldite LY5052 with Aradur H5052 and thermoplastic epoxy polyurethane mixed with tetrahydrofuran. These specimens were prepared using a hand layup method. Both adhesives were used to make eighty samples: forty for thermoplastic epoxy polyurethane with tetrahydrofuran and forty for thermosetting epoxy Araldite LY5052 with Aradur H5052. In order to determine the static strength of joints, tensile tests were conducted using a universal testing machine (UTM) where a tension–tension fatigue test was carried out on 50%, 70%, and 80% of the static load at which the joint failed. In the thermosetting double lap strap joint, the findings of both the elongation and fatigue tests showed an increase in strength throughout both the elongation and fatigue cycles. Thermosetting Kevlar hybrid joints have a high static and fatigue strength. Based on the results, thermosetting hybrid joints using Aradur H5052 and epoxy Araldite LY5052 had a static strength of 20.67 KN, whereas a thermoplastic adhesive joint had a static strength of 11.93 KN. Furthermore, the microscopic failure modes revealed that the mode of failure for the joints was cohesive and mixed-mode failure.