Zhixin Li

Dr. Zhixin Li


Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 September 2001 in The Journal of Physical Chemistry B
Verified
Journal Article
Closed access
GBGuangyue Bai
Guangyue Bai
JWJinben Wang
Jinben Wang
HYHaike Yan
Haike Yan
ZLZhixin Li
Zhixin Li
RTRobert. K. Thomas
Robert. K. Thomas

1 May 2007 in Experimental Thermal and Fluid Science
Verified
Journal Article
Closed access
LXLi Xiaowei
Li Xiaowei
HYHuan Yan
Huan Yan
JMJi-An Meng
Ji-An Meng
ZLZhixin Li
Zhixin Li

1 January 2005 in Journal of Enhanced Heat Transfer
Verified
Journal Article
Closed access
JMJi-An Meng
Ji-An Meng
ZCZe-Jing Chen
Ze-Jing Chen
ZLZhixin Li
Zhixin Li
ZGZeng-Yuan Guo
Zeng-Yuan Guo
The dependence of the Nusselt number on the time-averaged velocity and temperature fields was derived for turbulent convective heat transfer to show that the field coordination principle is also suitable for turbulent convective heat transfer. The features of convective heat transfer in tubes and the field coordination principle was used to develop an enhanced heat transfer tube—the alternating elliptical axis tube. The numerical and experimental results show that heat transfer is markedly enhanced with less additional flow drag than the other enhanced tube designs.

6 June 2024 in Buildings
Verified
Journal Article
Open access
PDF file
ZLZhixin Li
Zhixin Li
KXKaidong Xu
Kaidong Xu
NSNan Sun
Nan Sun
JWJina Wang
Jina Wang
KXKaiwang Xue
Kaiwang Xue
TSTongbao Sima
Tongbao Sima
The alkali-activated blast furnace slag is attracting significant attention in replacing Portland cement due to several characteristics similar to cement hydration. However, there are a few practical problems with commercial alkali activators, such as the fast setting time, relatively high costs, and significant CO2 emissions during preparation. Thus, discovering industrial residues possessing inherent alkalinity are urgent. This study proposes the use of carbide slag at levels of 0%, 5%, 10%, 15%, 20%, and 30% and alkali at levels of 1%, 2%, 3%, 4%, 5%, 6%, 8%, and 10% activated blast furnace slag. The compressive strength and microstructure of carbide slag and alkali-activated blast furnace slag (CAB) pastes were examined using X-ray diffraction analysis (XRD), Differential Scanning Calorimetry/Thermogravimetric Analysis (DSC/TG), Fourier transform infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM). The results revealed that the addition of carbide slag produced more hydrotalcite-like phase as well as decreased the content of ettringite (AFt) and the calcium–silicate–hydrate (C-S-H) gel, which decreased the compressive strength of the CAB pastes. At the age of 28 days, when the dosage was 5%, 10%, 15%, 20%, and 30%, the compressive strength of CAB mixes decreased by 2.1%, 7.1%, 9.2%, 9.8%, and 28.1%, respectively. The addition of NaOH promoted the formation of AFt, and there was an optimum level of NaOH corresponding to the high compressive strength of paste. At the age of 3 days and 7 days, the compressive strength reached its maximum at the dosage of 6% NaOH, which was 24.8 MPa and 36.3 MPa, respectively. However, at the ages of 14 days and 28 days, the compressive strength increased as the dosage of NaOH increased to 5%, which was 43.3 MPa and 44.5 MPa, respectively. The water curing could both enhance the early and later strength, the compressive strength of 23.3 MPa was gained at 3 days, and this increased by 16.3%, 24.0% and 36.9% at 7 days, 14 days and 28 days, respectively. Therefore, water curing was suitable for the strength development of CAB pastes.

1 January 2018 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
ZLZhixin Li
Zhixin Li
KXKaidong Xu
Kaidong Xu
JPJiahui Peng
Jiahui Peng
JWJina Wang
Jina Wang
XMXianwei Ma
Xianwei Ma
JNJishou Niu
Jishou Niu
In this work, Portland cement‐ (OPC‐) blended recycled plaster materials (R‐CP) were prepared to find out their hydration and mechanical properties. It was found that the hydration of R‐CP was accelerated by the rapid rehydrated ettringite (AFt), and the strength of R‐CP was decreased by the reduced hemihydrate content and low strength of rehydrated AFt and CaCO3. On the contrary, consistent with the previous studies, the strength of OPC‐blended plaster of Paris materials (POCP) was improved by the formation of AFt, Ca(OH)2, and CaCO3 that filled pores in the pastes. Therefore, a different strength development could be seen in POCP and R‐CP. In principle, these findings will lay a solid ground work for the utilization of recycled plaster.

1 January 2021 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
ZLZhixin Li
Zhixin Li
KXKaidong Xu
Kaidong Xu
JPJiahui Peng
Jiahui Peng
JWJina Wang
Jina Wang
JZJianwu Zhang
Jianwu Zhang
QLQingxiao Li
Qingxiao Li
Influence of the heating temperature and fineness on the hydration and mechanical property of recycled gypsum plaster was investigated to find the suitable heating temperature and fineness. According to the results, the setting time of recycled gypsum plaster increased with the increase of heating temperature, and the mechanical strength increased first and then decreased at a temperature of 165°C. Therefore, the suitable heating temperature was 165°C, and at this time, the initial setting time and final setting time were 8 min and 12.5 min, respectively, which met the requirements of the Chinese standard of GB/T 9776‐2008. The strength of recycled gypsum plaster increased with the increase of specific surface area, and the low water to plaster ratio and high strength were achieved when the specific surface area was 1526 m2/kg. Therefore, it can be concluded that the suitable heating temperature was 165°C and the suitable specific surface area was 1526 m2/kg considering the properties and economics of recycled gypsum plaster.