Current studies reveal the expectation that photovoltaic (PV) energy conversion will become the front-runner technology to stem against the extent of global warming by the middle of this century. In 2019, the passivated emitter and rear cell (PERC) design has taken over the majority of global photovoltaic solar cell production. The objective of this paper is to review the fundamental physics of the underlying cell architecture, its development over the past few decades to an industry main stream product, as well as an in-depth characterization of current cells and the future potential of the device structure. The early development of PERCs was set by an intriguing series of improvements starting in 1989 and resulting in a long-standing energy conversion efficiency record of 25.0% set up in 1999. It took a decade of intense technological development to implement this structure as an upgrade to existing production lines and another decade to increase the efficiency of industrially manufactured cells to over 22%. Our analysis of state-of-the-art large-area screen-printed PERCs is based on the pilot-line technology in the Photovoltaic Technology Evaluation Center at the Fraunhofer ISE, which is assumed to be representative of current state-of-the art cell processing. The main recent cell efficiency improvements have been achieved thanks to fine line metallization taking advantage of the high quality emitter formation and passivation and to improvements in material quality. In order to enhance the energy yield of the PV modules, innovations in interconnection technology like multibusbar and shingling technology as well as bifaciality are supported by PERC developments. Over the years, ongoing improvements have been made in the understanding of PERCs by analytical and numerical modeling of these devices. We show a study based on 3D numerical modeling and an extrapolation of the PERC device structure and technology to achieve an efficiency of 26%. This result surpasses earlier investigations due to the combination of technology components, as further improved front contact and emitter design as well as rear passivation and mirrors. We expect that PERCs can also play a strong role at the bottom of multijunction solar cells and will defend a strong position in global PV production beyond the end of the now starting decade.
21 February 2023 in Progress in Photovoltaics: Research and Applications
This work shows the first demonstration of thermal laser separation (TLS) and post‐metallization passivated edge technology (PET) applied to tunnel‐oxide passivated contact (TOPCon) shingle solar cells. The shingle solar cells with 26.46 mm × 158.75 mm size are separated from industrial full‐square TOPCon host solar cells. The singulation is performed either by TLS from the front side (emitter side) or by conventional laser scribe and mechanical cleaving (LSMC) from the rear side (emitter‐free side). The TLS optimized in this work yields up to 0.2%abs more efficient shingle cells after separation in comparison with LSMC‐separated shingle cells. The most promising PET sequence identified for the singulated TOPCon cells consists of depositing an 8‐nm‐thin aluminum oxide layer by thermal atomic layer deposition at a temperature below 200°C in conjunction with subsequent hotplate annealing at 250°C. Application of the PET yields a boost of up to 0.5%abs in energy conversion efficiency for edge‐passivated TOPCon shingle cells in comparison with their performance directly after separation. This efficiency‐increasing impact of the PET sequence is found not to be strongly dependent on the separation process applied. The most efficient TOPCon shingle cell after PET achieves an efficiency of 22.0% and has been singulated by TLS.
A novel plasma‐enhanced chemical vapour deposited (PECVD) stack layer system consisting of a‐SiOx:H, a‐SiNx:H, and a‐SiOx:H is presented for silicon solar cell rear side passivation. Surface recombination velocities below 60 cm/s (after firing) and below 30 cm/s (after forming gas anneal) were achieved. Solar cell precursors without front and rear metallisation showed implied open‐circuit voltages Voc values extracted from quasi‐steady‐state photoconductance (QSSPC) measurements above 680 mV. Fully finished solar cells with up to 20.0% energy conversion efficiency are presented. A fit of the cell′s internal quantum efficiency using software tool PC1D and a comparison to a full‐area aluminium‐back surface field (Al‐BSF) and thermal SiO2 is shown. PECVD‐ONO was found to be clearly superior to Al‐BSF. A separation of recombination at the metallised and the passivated area at the solar cell′s rear is presented using the equations of Fischer and Kray. Nuclear reaction analysis (NRA) has been used to evaluate the hydrogen depth profile of the passivation layer system at different stages.
This work presents the first results for the production of highly efficient solar cells with industrial processes using the PERC structure. Two batches of FZ and Cz wafers were conducted to prove the applicability of a transfer from the clean room to an industrial standard. The front and rear side metallization was done by a new pilot system using the sputtering technology. The investigation of solar cell results, series resistance, contact resistance and a optical analysis are discussed later on.
31 December 2010 in Solar Energy Materials and Solar Cells