Current studies reveal the expectation that photovoltaic (PV) energy conversion will become the front-runner technology to stem against the extent of global warming by the middle of this century. In 2019, the passivated emitter and rear cell (PERC) design has taken over the majority of global photovoltaic solar cell production. The objective of this paper is to review the fundamental physics of the underlying cell architecture, its development over the past few decades to an industry main stream product, as well as an in-depth characterization of current cells and the future potential of the device structure. The early development of PERCs was set by an intriguing series of improvements starting in 1989 and resulting in a long-standing energy conversion efficiency record of 25.0% set up in 1999. It took a decade of intense technological development to implement this structure as an upgrade to existing production lines and another decade to increase the efficiency of industrially manufactured cells to over 22%. Our analysis of state-of-the-art large-area screen-printed PERCs is based on the pilot-line technology in the Photovoltaic Technology Evaluation Center at the Fraunhofer ISE, which is assumed to be representative of current state-of-the art cell processing. The main recent cell efficiency improvements have been achieved thanks to fine line metallization taking advantage of the high quality emitter formation and passivation and to improvements in material quality. In order to enhance the energy yield of the PV modules, innovations in interconnection technology like multibusbar and shingling technology as well as bifaciality are supported by PERC developments. Over the years, ongoing improvements have been made in the understanding of PERCs by analytical and numerical modeling of these devices. We show a study based on 3D numerical modeling and an extrapolation of the PERC device structure and technology to achieve an efficiency of 26%. This result surpasses earlier investigations due to the combination of technology components, as further improved front contact and emitter design as well as rear passivation and mirrors. We expect that PERCs can also play a strong role at the bottom of multijunction solar cells and will defend a strong position in global PV production beyond the end of the now starting decade.
1 November 2015 in Solar Energy Materials and Solar Cells
We investigate different postseparation process routes for silicon heterojunction (SHJ) half solar cells, separated by thermal laser separation. SHJ half cells with and without aluminum oxide (Al 2 O 3 ) deposition as edge passivation layer undergo different annealing processes, including i) a hotplate; ii) an inline oven; and iii) an ultrafast light soaking process. SHJ half cells with an initial efficiency of 21.7% reach 21.9% after Al 2 O 3 deposition and inline oven annealing (pseudo fill factor, pFF , increase of 0.3% abs and series resistance R S decrease by −0.05 Ωcm 2 ). The light soaking process is known to lead to improved surface passivation and carrier transport for SHJ cells. For light soaking processed SHJ half cells, an 21.9% efficiency is obtained ( R S reduction by −0.13 Ωcm 2 and open-circuit voltage V OC increase by +2 mV compared to the initial half cell). By combining Al 2 O 3 deposition and subsequent light soaking, SHJ half cells reach 22.1% efficiency, resulting from the combined benefits for pFF , R S , and V OC of the two processes. No additional thermal annealing of the Al 2 O 3 layer is necessary, proving that the light soaking process is sufficient to activate the Al 2 O 3 passivation. This allows for a two-step postseparation process sequence, resulting in SHJ half cells featuring similar efficiencies to light soaking processed full cells. SHJ half cells, integrated into one-cell modules after Al 2 O 3 deposition and light soaking, show an efficiency advantage of +0.3% abs in comparison to modules with untreated half cells. Thus, we demonstrate the possibility of compensating separation losses for SHJ half cells and the transferability of the improvements to module level.
21 February 2023 in Progress in Photovoltaics: Research and Applications
This work shows the first demonstration of thermal laser separation (TLS) and post‐metallization passivated edge technology (PET) applied to tunnel‐oxide passivated contact (TOPCon) shingle solar cells. The shingle solar cells with 26.46 mm × 158.75 mm size are separated from industrial full‐square TOPCon host solar cells. The singulation is performed either by TLS from the front side (emitter side) or by conventional laser scribe and mechanical cleaving (LSMC) from the rear side (emitter‐free side). The TLS optimized in this work yields up to 0.2%abs more efficient shingle cells after separation in comparison with LSMC‐separated shingle cells. The most promising PET sequence identified for the singulated TOPCon cells consists of depositing an 8‐nm‐thin aluminum oxide layer by thermal atomic layer deposition at a temperature below 200°C in conjunction with subsequent hotplate annealing at 250°C. Application of the PET yields a boost of up to 0.5%abs in energy conversion efficiency for edge‐passivated TOPCon shingle cells in comparison with their performance directly after separation. This efficiency‐increasing impact of the PET sequence is found not to be strongly dependent on the separation process applied. The most efficient TOPCon shingle cell after PET achieves an efficiency of 22.0% and has been singulated by TLS.
This article investigates thermal laser separation (TLS) on p-type Czochralski-grown silicon (Cz-Si) passivated emitter and rear cells (PERC) and n-type Cz-Si heterojunction (SHJ) solar cells. The TLS comprises of two laser-based processes: the crack initiation by a scribe laser and the crack propagation by a cleave process leading to separated cells with smooth edge surfaces. The sole impact of the cleave process on the cells' passivation layers is examined by performing it without the initial scribe, not separating the samples. By means of photoluminescence imaging, different cleave laser powers PC on passivated PERC and SHJ cell precursors are investigated, and the optimum PC values are then chosen for the processing of metallized and fired host cells with half cell and shingle cell layouts. Both, the cleave process as well as the complete TLS process are then separately performed in order to investigate the effect of each individual process by SunsVOC measurements taken before and after processing. For monofacial PERC cells, a drop in pseudofill factor ΔpFF = - 0.3%abs is recorded after TLS of the host cell into five shingle cells with 31.35 mm cell width. The effect on bifacial SHJ cells is stronger with ΔpFF = - 2.1%abs. Thereby, the cleave process itself does not induce significant losses in the cell performance for both cell types. The main losses are attributed to the recombination at the newly created unpassivated edges after complete TLS.