17-4PH Stainless Steel is a mechanically high-performing alloy that is widely used across chemical and mechanical processing industries. The alloy is conventionally fabricated by cast methods, but emerging additive manufacturing techniques are presently offering an economic, efficient, and environmentally friendly alternative. Bound Powder Extrusion (BPE) is a relatively new additive manufacturing technique that is used to fabricate three-dimensional, free-form components. Investigation into the mechanical properties and behavior of 17-4PH stainless steel fabricated by BPE is vital to understanding whether this technique proposes a competitive substitute to the cast alloy within industry. Published literature has investigated the as-fabricated mechanical properties, microstructure, porosity, and post-processing heat treatment of the BPE alloy, with limited comparison evident among the papers. This paper, therefore, aims to review published findings on the mechanical properties of 17-4PH stainless steel produced by additive manufacturing techniques, with a key focus on BPE. It is important to highlight that this review study focuses on the MetalXTM 3D printer, manufactured by Markforged. This printer is among the widely utilized BPE 3D printers available in the market. The key results, together with the impact of post-heat treatments, were discussed and compared to provide a more comprehensive picture of the patterns that this alloy presents in terms of its microstructure and mechanical properties. This enables the manufacture of components relative to desired material performance, improving overall functionality. A comparison of yield strength, ultimate tensile strength (UTS), Young’s modulus, ductility, and hardness was made relative to microstructure, porosity, and density of published literature for the as-fabricated and post-heat-treated states, identifying areas for further research.
15 April 2026 in Progress in Additive Manufacturing
Additive manufacturing (AM) has recently gained attention as an effective approach for printing patient-specific, self-expanding Nitinol (NiTi alloy) stents with complex structural designs for the treatment of peripheral arterial disease (PAD). However, achieving the desired phase transformation temperature and superelastic performance remains challenging due to compositional variations, phase imbalance and microstructural inhomogeneities introduced during the printing process. In this study, self-expanding Nitinol stents with a zero Poisson’s ratio (ZPR) structural design were fabricated via laser powder bed fusion (PBF-LB). The printed stents showed no evidence of cracks or structural defects, confirming PBF-LB’s capability to produce mechanically sound stent geometries. However, the as-printed stents exhibited an austenite finish (A f ) temperature above 80 °C, which is incompatible with body-temperature functionality. To address this, a systematic post-heat treatment strategy was developed by varying temperature and time, with the effects evaluated through transition temperature measurements and previously unreported cyclic three-point compression testing. The optimised treatment, solution annealing at 850 °C for 15 min followed by aging at 500 °C for 15 min, produced a homogenised microstructure with surface Ni diffusion, effectively reducing the A f temperature to 35 °C. Under these conditions, the stents demonstrated excellent superelastic performance at body temperature, achieving a 93.6% recovery ratio in the first compression cycle, and 97.9% after ten cycles, representing outstanding superelastic recovery compared with previously reported PBF-LB-printed NiTi. Therefore, this study establishes a viable post-processing heat-treatment protocol that provides a practical framework for manufacturing NiTi implants via AM, while maintaining the desired functional properties of self-expanding ZPR stents. Graphical abstract
Stenting is a minimally invasive treatment used in managing peripheral artery disease (PAD). However, clinical challenges persist, including in-stent thrombosis and restenosis, primarily driven by axial foreshortening or elongation and suboptimal balance between radial stiffness and flexibility inherent to conventional stent designs. This study proposes an innovative arrow-shaped geometry exhibiting zero Poisson’s ratio (ZPR) behaviour for 3D-printed self-expanding Nitinol stents. The complete stent deployment process was modelled using finite element analysis (FEA), including radial crimping and subsequent expansion to enable systematic parametric investigation while accounting for µ-3D printing constraints. Response surface methodology (RSM) rigorously evaluated mechanical performance, defining peak stress, chronic outward force (COF), radial resistive force (RRF), and foreshortening (FS) as constraint and objective functions within the optimisation framework. The optimised ZPR stent achieved favourable performance: extremely low foreshortening (|FS| ≤ 0.12%), representing outstanding axial stability compared with previously reported self-expanding stents, and a well-balanced radial response with ~50% higher radial strength than positive Poisson’s ratio (PPR) structures, while 16.67% lower than negative Poisson’s ratio (NPR) counterparts. These results highlight the ZPR stent’s capability to minimise axial deformation while maintaining adequate radial support, highlighting substantial potential for precise, stable deployment in PAD applications.