The plasticity and transformation are important for the toughness and ductility of hcp titanium under shock loading. However, three questions remain outstanding: (i) what mechanisms govern the plasticity and transformation, (ii) how does the microstructure, i.e., grain boundaries (GBs) and crystallographic orientations, affect them, and (iii) does the transformation take place dependent on the plasticity, such as dislocation slips? We conduct large-scale nonequilibrium molecular dynamics simulations to study shock-induced plasticity and phase transformation in hexagonal columnar nanocrystalline Ti. Significant anisotropy and strong dependence on crystallographic orientation are presented during shock-induced plasticity and phase transformation. The shock first prompts “heterogeneous” dislocation slips and lattice reorientation, via coupling deformation twinning and slips. Then, the on-going plastic deformation induces a “heterogeneous” phase transformation at lower impact velocities or a “homogeneous” solid-state disordering at higher impact velocities. The phase transformation mostly obeys the TAO-1 pathways originated from GBs, while a few of them are governed by Silcock mechanisms within the grains. The TAO-1 and Silcock-governed transformations stem from the emission and propagation of basal-prismatic and prismatic stacking faults, respectively. At the release/tension stage, a transformation occurs, acting as the reversed process of the transformation at the compression stage. Meanwhile, structural recovery and spallation initiate in the extending tension area induced by the release fans. Serving as the nucleation of the plasticity, phase transformation, and spallation, GBs play the key role during the loading.
11 February 2019 in Physical Chemistry Chemical Physics
We present an atomistic simulation study on the compositional arrangements throughout Cu–Pt icosahedra, with a specific focus on the effects of inherent strain on general segregation trends. The coexistence of radial and site-selective segregation patterns is found in bimetallic nanoparticles for a broad range of sizes and compositions, consistent with prior analytical and atomistic models. Through a thorough comparison between the composition patterns and strain-related patterns, it is suggested that the presence of gradient and site-selective segregation is natural to largely relieve the inherent strain by preferential segregation of big atoms at tensile sites and vice versa, as previously hypothesized in the literature. Analogous to the case of single crystal particles, Cu-rich surface and damped oscillations can also be found in the outer shells of icosahedra, which are dominated by the lowering of both the surface energy and the chemical energy. The thermodynamic stability of segregated icosahedra is similar to segregated cuboctahedra but higher than disordered bulk alloys, validating prior thinking that element segregation driven by strain relief can extend the stability range of multiply-twinned nanoparticles. Our work sheds new light on understanding strain-induced segregation in multiply-twinned nanosystems that have elements with large lattice mismatch and strong alloying ability.
1 February 2018 in Computational Materials Science
Two-dimensional (2D) layered halide perovskites have been shown to enable improved long-term stability in comparison to the well-known three-dimensional hybrid organic–inorganic halide perovskites. The optoelectronic properties of the 2D perovskites are strongly influenced by the chemical nature of the charge transport layer. In this work, we fabricated Ruddlesden–Popper 2D perovskite solar cells (PSCs) using solution processed inorganic NiOx and a C60 : C70 (1 : 1) mixture as the hole and electron transport layers, which significantly improved the performance of the 2D PSCs. Time resolved photoluminescence measurements indicate the shortened lifetime of excitons, which demonstrates the excellent charge extraction properties. The PSCs based on these inorganic charge transport materials (CTMs) exhibit an average power conversion efficiency (PCE) of 14.1%, which is higher than that (12.3%) of PSCs using organic CTMs of poly(3,4-ethylenedioxythiophene) : poly(styrenesulfonate) (PEDOT:PSS) and phenyl-C61-butyric acid methyl ester (PCBM). Compared with PEDOT:PSS and PCBM based cases, the PSCs using inorganic CTMs also show improved long-term stability, with the PCE degradation significantly suppressed from 20% to 12% after a measurement of 15 days. The best PSCs using NiOx and C60 : C70 show a high PCE of 14.4%, with a stable power output and negligible hysteresis.
The influence of an exciton delocalization ligand on the structural, electronic, optical, and charge transfer properties of Cd 33 S 33 quantum dot were elucidated.
21 May 2018 in Physical Chemistry Chemical Physics
We systematically investigate the collapse of a set of open-cell nanoporous Cu (np-Cu) materials with the same porosity and shape but different specific surface areas, during thermal annealing, by performing large-scale molecular dynamics simulations. Two mechanisms govern the collapse of np-Cu. One is direct surface premelting, facilitating the collapse of np-Cu, when the specific surface area is less than a critical value (∼2.38 nm−1). The other is recrystallization followed by surface premelting, accelerating the sloughing of ligaments and the annihilation of voids, when the critical specific surface area is exceeded. Surface premelting results from surface reconstruction by prompting localized “disordering” and “chaos” on the surface, and the melting temperature reduces linearly with the increase of the specific surface area. Recrystallization is followed by surface premelting as the melting temperature is below the supercooling point, where a liquid is unstable and instantaneously recrystallizes.