To meet the demand for energy-efficient and, at the same time, durable, functional components, the improvement of tribological behavior is playing an increasingly important role. One approach to reducing friction in lubricated tribological systems is the microtexturing of the surfaces tailored to the application, but in most cases, this leads to increased manufacturing costs and thus often makes their use in industry more difficult. In this work, we, therefore, present an approach for an efficient design and fully integrated production process using a cam tappet as an example. For the used cam tappet contact, we first determined the optimal texture geometries using two differently complex EHL (elastohydrodynamic lubrication) simulation models. Based on these, textured tappets were manufactured in a combined manner using sheet-bulk metal-forming and deposition with a diamond-like-carbon (DLC) coating for additional wear protection without further post-processing of the coating. We show that the simulation approach used has a rather subordinate influence on the optimization result. The combined forming of components with textured surfaces is limited by the local material flow, the resulting texture distortion, and tool wear. However, a targeted process design can help to exploit the potential of single-stage forming. The applied DLC coating has good adhesion and can completely prevent wear in subsequent reciprocal pin-on-disc tests, while the friction in the run-in behavior is initially higher due to the soothing effects of the coating. The experiments also show a tendency for shallow textures to exhibit lower friction compared to deeper ones, which corresponds to the expectations from the simulation.
Friction losses are present in all kinds of technical systems. This is always associated with additional energy consumption, which can be partly avoided as it arises. Energy savings can be achieved by a wide range of approaches. The application of friction reducing coatings on bodies in relative motion is widespread. The coating of parts is however only suitable to a limited extent for the production in large batches. Therefore, research approaches consider alternative methods to achieve friction reductions. A promising approach is the integration of miniaturized pockets on the surface of the component. In lubricated contacts, the lubricant can then accumulate in these indentations. The relative motion between two bodies thus builds up a hydrodynamic pressure and consequently reduces friction. Forming technology is suitable for the efficient production of metallic components in large quantities. The aim of this study is therefore to identify challenges in the integration of micro coining in established forming processes. Two processes from sheet metal forming and bulk metal forming are investigated. In a combined experimental and numerical approach, process-specific challenges are derived regarding the texturing process and the numerical process modelling for combined micro coining. The analysis is carried out on a cup geometry, as used in the automotive sector as tappets in the valve train. The case hardening steel 16MnCr5 (1.7131) is used as workpiece material.
15 September 2024 in Materials Research Proceedings
A rising demand on resource efficient and highly functional products causes conventional metal forming processes to the reach their limits. For this reason, sheet-bulk metal forming (SBMF) for the production of thin-walled components with various filigree functional elements has been widely investigated in recent years. However, there is a research gap in the understanding of approaches within this process class for producing helical gears. These are in high demand in industrial environments due to their smooth running capabilities. In this study, a process combination of deep drawing and lateral extrusion for the production of helical lightweight gears is therefore examined. In the reference variant, the mild deep-drawing steel DC04 with a sheet thickness of t0 = 2.0 mm is formed with a 20° helical die. General process limits are derived depending on the die filling of the tool-side cavities. In addition, the influence of the gear angle on process and component target variables is analyzed and discussed.
9 September 2022 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
In industrial sectors like medical and automotive engineering, the demand for metal components with a high function integration brings conventional production technologies to their limits. This motivates research on innovative processes, which can meet the present requirements on fabricated parts and consequently also the demands on the applied manufacturing process. Part-sided, a high strength, narrow dimensional tolerances and a large functionality is often desired. In addition, an economical component production calls for processes with high material utilization as well as the achievement of short cycle times. The process class of sheet-bulk metal forming, characterized by the application of bulk forming operations on sheet metal, offers the potential to meet these requirements. Currently, sheet-bulk metal forming is mainly used for the fabrication of components with functional elements of macroscopic size. However, microscopic elements and micro-textured surfaces are of high interest for applications in prosthetics and automotive engineering. The objective of this study is therefore to develop an application-oriented method for the design, production and testing of 16MnCr5 metal components, manufactured by a combined process of sheet-bulk metal forming, creating a defined microstructure on the surface. Since the selection of a suitable texture layout and geometry is crucial for tribological optimization, these are designed for their application using numerical elastohydrodynamic lubricant simulations. The contact conditions occurring in the application are modelled as realistically as possible so that texture designs suitable for production can subsequently be compared in test bench trials. It is shown that the tappets produced by forming technology can be efficiently investigated with the test rig presented.
Due to the ongoing technological development, the demand for geometrically complicated high performance parts with great functional density is increasing. Often, the use of sheet metal is a beneficial approach in manufacturing technology to meet the requirements on components regarding material strength and lightweight construction goals. The forming of therefore required complex sheet metal part geometries with integrated functional elements cause the need for a three dimensional material flow. Sheet-bulk metal forming, characterized by the application of bulk forming operations on sheet metals, is a suitable approach to produce such components. A challenge is the material flow control, resulting in an insufficient die filling of the functional elements. The use of tailored blanks with a defined sheet thickness distribution is an auspicious approach to face this challenge in subsequent forming processes. In the presented work, semi-finished products with a continuous thickness profile manufactured by orbital forming are applied in a full forward extrusion process. By an additional implementation of a heat treatment, the tailored blanks undergo a recrystallization process that causes a softening of the strain hardened material. In this paper, the potential of a heat treatment in the process class of sheet-bulk metal forming is shown by characterizing the geometrical and mechanical properties of the functional components by applying the mild deep drawing steel DC04 with an initial sheet thickness of t0 = 2.0 mm.