Nao Terasaki

Dr. Nao Terasaki

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 September 2021 in The Journal of Adhesion
Verified
Journal Article
Closed access
NTNao Terasaki
Nao Terasaki
KSK. Shimamoto
K. Shimamoto
HAH. Akiyama
H. Akiyama
CSC. Sato
C. Sato
Double lap joints were prepared using epoxy adhesive and aluminum plates, and their high-temperature strength properties were studied. Tensile, thermal aging, creep, and cyclic fatigue tests were performed to systematically investigate the effects of the aging temperature, testing temperature, stress waveform, and stress ratio on the strength and fracture morphology of the double lap joints. When the specimen was exposed to 135°C, the strength decreased significantly. Also, the relationship between the test temperature and shear strength could be expressed using an equation obtained from thermal activation theory. Additionally, in the fatigue test at room temperature, the strength of the specimen subjected to constant stress was higher than that of the specimen subjected to cyclic strain. The effect of creep deformation increased in the creep test at high temperatures, and therefore, the strength decreased significantly.

17 May 2021 in The Journal of Adhesion
Verified
Journal Article
Closed access
NTNao Terasaki
Nao Terasaki
KSK. Shimamoto
K. Shimamoto
HAH. Akiyama
H. Akiyama
CSC. Sato
C. Sato
The effect of cyclic moisture-absorption/desorption on adhesive strength was investigated using water at 23°C. Bulk plates and open face lap joints were prepared using epoxy adhesive, and their weight transition and shear strength were measured. The diffusion coefficient of the absorption process increased with the number of cycles and reached a constant value. In contrast, the diffusion coefficient of the desorption process was not affected by the number of cycles. As a part of the calcium carbonate disappeared from the surface, the weight of the bulk plates was reduced, and this weight reduction was irreversible. However, the strength of the lap joint was not significantly damaged by moisture absorption at 23°C.

11 May 2022 in The Journal of Adhesion
Verified
Journal Article
Closed access
NTNao Terasaki
Nao Terasaki
YSY. Sekiguchi
Y. Sekiguchi
KSK. Shimamoto
K. Shimamoto
HAH. Akiyama
H. Akiyama
CSC. Sato
C. Sato
In this study, the relationship between the energy release rate (G1C), crack propagation rate (da/dN), and the fracture morphology of specimens with deteriorated adhesives after moisture absorption were investigated through the double cantilever beam (DCB) method. The specimens were prepared using a thermosetting epoxy adhesive based on compound carboxyl-terminated butadiene–nitrile rubber and Al 6061-T6 adherends. To accelerate the deterioration of the adhesives, open-faced specimens were immersed in water at 63°C at varying durations. Prior to the assembly of the DCB specimens, the adherends were either treated using acidic solutions or sand blasted. Consequently, the effect of the moisture deterioration of adhesive and the surface treatment performed on the adherend on the fracture morphology was studied. Furthermore, the relationship between G1C and da/dN was systematically investigated. At a constant crack opening speed, the failure mode changed from cohesive to interfacial fracture, and then reverted back cohesive fracture as the deterioration of the specimens progressed due to increasing immersion time. Interfacial fracture was not observed for the specimens with sandblasted adherends. Lastly, a decrease in da/dN was not observed even with increasing G1C values of the immersed specimens because interfacial fracture was easy to occur when the cyclic strains were applied.

19 March 2020 in The Journal of Adhesion
Verified
Journal Article
Closed access
NTNao Terasaki
Nao Terasaki
KSK. Shimamoto
K. Shimamoto
HAH. Akiyama
H. Akiyama
CSChiaki Sato
Chiaki Sato
The improvement in adhesion technology for joining different types of materials has led to expectations of weight reduction in cars and commercial vehicles. Various levels of stress and stress ratios are loaded onto the joints of such transport vehicles. Therefore, the fatigue shear strength of an adhesive lap joint is important. This study is related to the fatigue properties of structural adhesive joints. Lap-joint specimens using epoxy adhesive were prepared, and fatigue tests with four different stress ratios were conducted. Subsequently, the fatigue limit diagram was plotted, and the effect of stress ratio on the fatigue limit was investigated. Moreover, the strength of the specimens subjected to various cyclic stress levels was investigated systemically. With cyclic shear stress, the influence of the shear stress amplitude on the resistance to fatigue failure was more significant than that of the number of cycles. The specimens that endured the fatigue tests maintained approximately the same shear strength as that of the as-received specimens. The findings of this study can provide important guidance for the design of a car body.

29 October 2020 in The Journal of Adhesion
Verified
Journal Article
Closed access
NTNao Terasaki
Nao Terasaki
KSK. Shimamoto
K. Shimamoto
HAH. Akiyama
H. Akiyama
CSC. Sato
C. Sato
The effect of strain rate on the mechanical properties of two epoxy adhesives was investigated by conducting experiments on dumbbell-shaped specimens prepared from the adhesives. The tensile rate was changed stepwise from 5.2 × 10–5 to 1.2 × 106 mm/min, and the yield stress, Young’s modulus, elongation, and tensile strength were evaluated. The yield stress and tensile strength showed a clear dependence on the strain rate. The results from this study allowed us to propose a procedure for predicting the creep strength and high-rate impact strength from the results of a simple tensile test.

13 July 2023 in Polymer Testing
Verified
Journal Article
Open access
NTNao Terasaki
Nao Terasaki
KSKazumasa Shimamoto
Kazumasa Shimamoto
HAHARUHISA AKIYAMA
HARUHISA AKIYAMA
NTNao Terasaki
Nao Terasaki
CSChiaki Sato
Chiaki Sato