2 April 2015 in The Journal of Adhesion
Thermal effects on welded joints between fiber-reinforced thermoplastics (FRTPs) and metals have been investigated theoretically and experimentally. Because FRTPs use thermoplastics as the matrix resin, they have advantages over fiber-reinforced thermoset plastics (FRPs or FRSPs), including the ability to be welded. When dissimilar materials are welded together, however, thermal stress occurs due to the different thermal expansions of the materials and affects the energy release rate of the joint. Therefore, a method for evaluating the true energy release rate, including the effect of thermal stress, is necessary for strength evaluation tests. Although several theories that compensate for the thermal stress and evaluate the true energy release rate have already been proposed, they require parameters that are difficult to measure. Therefore, it is difficult to apply them in experimental investigations. In this article, a theoretical method with easily measurable parameters is proposed to calculate the energy release rate of welded double cantilever beam (DCB) joints. The effect of the thermal stress on the critical energy release rate is discussed in terms of the experimental results of a welded DCB specimen composed of a FRTP and an aluminum alloy.
27 September 2021 in The Journal of Adhesion
To improve the long-term reliability of adhesively bonded joints, it is important to evaluate the degradation of adhesives on exposure to high-temperature and high-humidity environments. Further, it is important to evaluate the change in material properties, such as mechanical residual strength. Although Fourier transform infrared (FTIR) spectroscopy is widely used to investigate the chemical structures in materials, it is difficult to identify the cause of degradation due to the complex composition of adhesives. This study aimed to develop a simple method for extracting the features related to degradation using FTIR spectroscopy, and to estimate the mechanical residual strength. The surface of the adhesives after immersion exposure to water at a high temperature was analysed using FTIR spectroscopy, and their mechanical strength was measured. The correspondence between them was demonstrated using machine learning. Several linear regression methods were used and compared; the model based on Lasso regression was determined to be the most suitable for extracting features and estimating residual strength. Furthermore, it was indicated that the developed model could be used to identify areas where there is a loss of strength.
1 June 2016 in International Journal of Adhesion and Adhesives
19 March 2020 in The Journal of Adhesion
The improvement in adhesion technology for joining different types of materials has led to expectations of weight reduction in cars and commercial vehicles. Various levels of stress and stress ratios are loaded onto the joints of such transport vehicles. Therefore, the fatigue shear strength of an adhesive lap joint is important. This study is related to the fatigue properties of structural adhesive joints. Lap-joint specimens using epoxy adhesive were prepared, and fatigue tests with four different stress ratios were conducted. Subsequently, the fatigue limit diagram was plotted, and the effect of stress ratio on the fatigue limit was investigated. Moreover, the strength of the specimens subjected to various cyclic stress levels was investigated systemically. With cyclic shear stress, the influence of the shear stress amplitude on the resistance to fatigue failure was more significant than that of the number of cycles. The specimens that endured the fatigue tests maintained approximately the same shear strength as that of the as-received specimens. The findings of this study can provide important guidance for the design of a car body.
1 December 2016 in International Journal of Solids and Structures
10 June 2020 in The Journal of Adhesion
Adhesive properties are often affected by water. In this study, to clarify the water-resistant properties of a thermosetting epoxy adhesive containing dicyandiamide (DICY) and carboxyl-terminated butadiene acrylonitrile rubber (CTBN), immersion tests of open-faced specimens and bulk specimens in water were performed, and the changes in the properties were investigated in terms of chemistry and mechanical strength. After immersing the open-faced specimens in water, the mechanical strengths were evaluated by two different methods: interfacial cutting method and secondary bonding method. Using both methods, a decrease in strength with immersion time was obtained, and the tendencies of the strength change were found to be very similar for the different evaluation methods. Chemical changes were also evaluated by infrared spectroscopy. Through periodical measurements of the infrared spectra of a fully-cured bulk adhesive specimen during water immersion, the chemical degradation of the epoxy adhesive containing DICY and CTBN was investigated, revealing an association with the change in mechanical strength in which hydrolysis of the cyano groups in DICY and CTBN led to a decrease in strength. Strength recovery experiments were also conducted by drying the specimens after water immersion, determining that the mechanical recovery strength changed with water temperature and immersion time.