Ba2SiO4−δN2/3δ:Eu2+ (BSON:Eu2+) materials with different N3− contents were successfully prepared and characterized. Rietveld refinements showed that N3− ions were partially substituted for the O2− ions in the SiO4-tetrahedra because the bond lengths of Si‒(O,N) (average value = 1.689 Å) were slightly elongated compared with those of Si‒O (average value = 1.659 Å), which resulted in the minute compression of the Ba(2)‒O bond lengths from 2.832 to 2.810 Å. The average N3− contents of BSON:Eu2+ phosphors were determined from 100 nm to 2000 nm depth of grain using a secondary ion mass spectrometry (SIMS): 0.064 (synthesized using 100% α-Si3N4), 0.035 (using 50% α-Si3N4 and 50% SiO2), and 0.000 (using 100% SiO2). Infrared (IR) and X-ray photoelectron spectroscopy (XPS) measurements corroborated the Rietveld refinements: the new IR mode at 850 cm−1 (Si‒N stretching vibration) and the binding energy at 98.6 eV (Si-2p) due to the N3- substitution. Furthermore, in UV-region, the absorbance of N3−-substituted BSON:Eu2+ (synthesized using 100% α-Si3N4) phosphor was about two times higher than that of BSO:Eu2+ (using 100% SiO2). Owing to the N3− substitution, surprisingly, the photoluminescence (PL) and LED-PL intensity of BSON:Eu2+ (synthesized using 100% α-Si3N4) was about 5.0 times as high as that of BSO:Eu2+ (using 100% SiO2). The compressive strain estimated by the Williamson−Hall (W−H) method, was slightly increased with the higher N3− content in the host-lattice of Ba2SiO4, which warranted that the N3- ion plays an important role in the highly enhanced PL intensity of BSON:Eu2+ phosphor. These phosphor materials could be a bridgehead for developing new phosphors and application in white NUV-LEDs field.
This study systematically investigated an atmospheric pressure plasma reactor with a centered single pin electrode inside a dielectric tube for depositing the polyaniline (PANI) thin film based on the experimental case studies relative to variations in pin electrode configurations (cases I, II, and III), bluff-body heights, and argon (Ar) gas flow rates. In these cases, the intensified charge-coupled device and optical emission spectroscopy were analyzed to investigate the factors affecting intensive glow-like plasma generation for deposition with a large area. Compared to case I, the intense glow-like plasma of the cases II and III generated abundant reactive nitrogen species (RNSs) and excited argon radical species for fragmentation and recombination of PANI. In case III, the film thickness and deposition rate of the PANI thin film were about 450 nm and 7.5 nm/min, respectively. This increase may imply that the increase in the excited radical species contributes to the fragmentation and recombination due to the increase in RNSs and excited argon radicals during the atmospheric pressure (AP) plasma polymerization to obtain the PANI thin film. This intense glow-like plasma generated broadly by the AP plasma reactor can uniformly deposit the PANI thin film, which is confirmed by field emission-scanning electron microscopy and Fourier transform infrared spectroscopy.
This study investigates the structural phase and dielectric properties of poly(vinylidenefluoride-co-trifluoroethylene) (P[VDF–TrFE]) thin films grown via atmospheric pressure (AP) plasma deposition using a mixed polymer solution comprising P[VDF–TrFE] polymer nano powder and dimethylformamide (DMF) liquid solvent. The length of the glass guide tube of the AP plasma deposition system is an important parameter in producing intense cloud-like plasma from the vaporization of DMF liquid solvent containing polymer nano powder. This intense cloud-like plasma for polymer deposition is observed in a glass guide tube of length 80 mm greater than the conventional case, thus uniformly depositing the P[VDF–TrFE] thin film with a thickness of 3 μm. The P[VDF–TrFE] thin films with excellent β-phase structural properties were coated under the optimum conditions at room temperature for 1 h. However, the P[VDF–TrFE] thin film had a very high DMF solvent component. The post-heating treatment was then performed on a hotplate in air for 3 h at post-heating temperatures of 140 °C, 160 °C, and 180 °C to remove DMF solvent and obtain pure piezoelectric P[VDF–TrFE] thin films. The optimal conditions for removing the DMF solvent while maintaining the β phases were also examined. The post-heated P[VDF–TrFE] thin films at 160 °C had a smooth surface with nanoparticles and crystalline peaks of β phases, as confirmed by the Fourier transform infrared spectroscopy and XRD analysis. The dielectric constant of the post-heated P[VDF–TrFE] thin film was measured to be 30 using an impedance analyzer at 10 kHz and is expected to be applied to electronic devices such as low-frequency piezoelectric nanogenerators.
The discoloration switching appearing in the initial and final growth stages of 4H-silicon carbide (4H-SiC) single crystals grown using the physical vapor transport (PVT) technique was investigated. This phenomenon was studied, investigating the correlation with linear-type micro-pipe defects on the surface of 4H-SiC single crystals. Based on the experimental results obtained using time-of-flight secondary ion mass spectrometry (ToF-SIMS) and micro-Raman analysis, it was deduced that the orientation of the 4H-SiC c-axis causes an axial change that correlates with low levels of carbon. In addition, it was confirmed that the incorporation of additional elements and the concentrations of these doped impurity elements were the main causes of discoloration and changes in growth orientation. Overall, this work provides guidelines for evaluating the discoloration switching in 4H-SiC single crystals and contributes to a greater understanding of this phenomenon.