Roberto Schroeder

Dr. Roberto Schroeder

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 May 2009 in Materials and Corrosion
Verified
Journal Article
Closed access
PDF file
RSRoberto Schroeder
Roberto Schroeder
IMI. L. Müller
I. L. Müller

14 June 2024 in Metals
Verified
Journal Article
Open access
PDF file
VCVictor Velho de Castro
Victor Velho de Castro
CECristiano Ev
Cristiano Ev
LNLeandro Câmara Noronha
Leandro Câmara Noronha
MBMatheus da Silva Bullmann
Matheus da Silva Bullmann
LELouise Etcheverry
Louise Etcheverry
CMCélia de Fraga Malfatti
Célia de Fraga Malfatti
This study aims to assess the effectiveness of water-based formulations featuring m-2HEAOL and talc particles in deep drawing applications. The coefficient of friction (COF) was measured through bending under tension (BUT) tests, while the interaction mechanism between protic ionic liquid (PIL) and talc particles was analysed using FTIR, XPS, and TGA analyses. The results indicate that the formulation containing 8 wt% PIL and 0.5 wt% talc exhibited the best lubricating performance. This was due to the interaction of the PIL oleate molecules with the Mg found in the talc basal layer, which enhanced the cleavage capacity of this mineral, ultimately improving the lubricity of the formulation.

28 June 2024 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
MDMatheus Thedy Dorneles
Matheus Thedy Dorneles
VCVictor Velho de Castro
Victor Velho de Castro
AJAdilar Gonçalves dos Santos Junior
Adilar Gonçalves dos Santos Junior
CACesar Aguzzoli
Cesar Aguzzoli
Antonio Marcos Helgueira de AndradeAntonio Marcos Helgueira de Andrade
Antonio Marcos Helgueira de Andrade
CMCélia de Fraga Malfatti
Célia de Fraga Malfatti

31 May 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
HHHeitor Hatwig
Heitor Hatwig
VCVictor Velho de Castro
Victor Velho de Castro
MBMatheus Bullmann
Matheus Bullmann
RSRoberto Schroeder
Roberto Schroeder
CMCélia de Fraga Malfatti
Célia de Fraga Malfatti
This research aims to investigate and quantify potential damage resulting from induced superficial defects on the surface of wires use on tensile armor of flexible pipes. Different values of kt factors and H2S concentration in aggressive gas mixtures with CO2, were analysed to determine the operational conditions that do not result in rupture of the tensile reinforcement during service, under the conditions studied. The tests were based on NACE TM0316 standard, using a 4-point bend test. Two superficial notches were created, which generated known stress concentration factor Kt values of 1.5 and 2.0, and three gaseous concentrations (220, 700, and 1100 ppm of H2S in CO2) were used. After bending tests, the samples were evaluated by metallographic and fractographic analysis, weight loss and liquid penetrant inspection. The results were then analysed using analysis of variance (ANOVA). Only the samples exposed to 220 ppm of H2S in CO2 did not rupture at both Kt values. However, for the Kt value of 2.0, cracks were observed in the longitudinal direction of the wires, originating from the machined notch. Additionally, the samples exposed to 700 ppm and 1100 ppm of H2S had a significantly higher damage score (approximately 15x) than the samples exposed to 220 ppm, regardless of the Kt value.

24 July 2026 in Metals
Verified
Journal Article
Open access
PDF file
VCVictor Velho de Castro
Victor Velho de Castro
CECristiano Ev
Cristiano Ev
LNLeandro Câmara Noronha
Leandro Câmara Noronha
MBMatheus da Silva Bullmann
Matheus da Silva Bullmann
LELouise Etcheverry
Louise Etcheverry
CMCélia de Fraga Malfatti
Célia de Fraga Malfatti
There was an error in the original publication