DIN 16MnCr5 is commonly used in mechanical engineering contact applications such as gears, joint parts, shafts, gear wheels, camshafts, bolts, pins, and cardan joints, among others. This study examined the microstructural and mechanical properties and tribological behavior of different surface treatments applied to DIN 16MnCr5 steel. The samples were hardened at 870 °C for 15 min and then quenched in water. The surface conditions evaluated were as follows: quenched and tempered DIN 16MnCr5 steel samples without surface treatments (control group), quenched and tempered DIN 16MnCr5 steel samples with gas-nitriding at 560 °C for 6 h, quenched and tempered DIN 16MnCr5 steel samples with pack boriding at 950 °C for 4 h, and quenched and tempered DIN 16MnCr5 steel samples with duplex gas-nitriding and pack boriding. Microstructure characterization was carried out using metallographic techniques, optical microscopy, scanning electron microscopy with energy-dispersive spectroscopy, and X-ray diffraction. The mechanical properties were assessed through microhardness and elastic modulus tests using nanoindentation. The tribological behavior was evaluated using pin-on-disc tests following the ASTM G99-17 standard procedure under dry sliding conditions. The results indicated that the surface treated with duplex gas-nitriding and pack boriding exhibited the highest wear resistance and a reduced coefficient of friction due to improved mechanical properties, leading to increased hardness and elastic modulus.
This study investigates the effects of surface thermochemical treatments using boriding, nitriding, and boronitriding on the microstructure and mechanical properties of martensitic stainless steel AISI 420 ESR. Powder-pack boriding, gas nitriding, and sequential boronitriding processes were applied to enhance surface hardness, wear resistance, and adhesion. The microstructural and mechanical properties of the surface samples were analyzed using scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, microhardness, and nanoindentation testing. Tribological behavior was analyzed using a pin-on-disk tribometer under dry-sliding wear conditions, with applied normal loads of 5 N and 10 N and a sliding distance of 1000 m. The results showed that the borided samples exhibited the highest surface hardness, up to 1182 HV0.05, as well as brittle fracture and spallation with poor adhesion, while the boronitrided layer offered excellent adhesion. The boronitriding condition demonstrated a synergistic balance, combining high wear resistance (5.92 × 10−7 mm3N−1m−1 and 4.96 × 10−7 mm3N−1m−1) and reduced friction (~0.78 and ~0.67) for loads of 5 N and 10 N, respectively, without brittle fractures on the coating layer. These results confirm that duplex coating treatment is an effective strategy for improving the surface performance of AISI 420 ESR components subjected to severe operating conditions.
In this work, a novel approach for a wear testing is investigated using a spherical, diamond-coated mounted point in a pin-on-disk tribometer to simulate two-body abrasion. The procedure establishes a new type of testing method for simulating abrasive wear with particularly harsh conditions. For validation, tests were conducted on both quenched and tempered as well as on additionally nitrided samples made of 16MnCr5. The design of the experiments is based on the ASTM G99-17 standard for pin-on-disk tests. A characteristic wear track is produced, which is formed by the recurring influence of the diamond wear particles. Due to the shape of the wear track, it is necessary to use a modified approach for evaluating the tests compared to the standard. The main focus of this work is on the effect of the aggressive abrasive grinding tool on hard surface layers and the repeatability of the test results. It is demonstrated that under the same test conditions, the heat treatment conditions of the samples can be clearly and repeatedly distinguished based on the wear curves. Due to the highly abrasive effect, the method is suitable for investigating procedures to enhance the surface hardness or wear resistance of surfaces.
Austenite grains that underwent the f.c.c. to b.c.c. (or b.c.t.) transformation are typically composed of 24 Kurdjumov–Sachs variants that can be categorized by three axes of Bain transformations; thus, a complete transformation generally displays 3-fold symmetry in (001) pole figures. In the present work, crystallographic symmetry in 42CrMo4 steel austempered below martensite start temperature was investigated with the help of the orientation distribution function (ODF) analysis based on the FEG-SEM/EBSD technique. It is shown that, upon phase transformations, the specimens contained 6-fold symmetry in all (001), (011), and (111) pole figures of an ODF. The ODF analysis, verified by theoretical modeling, showed that under plane-strain conditions cracks prefer to propagate through areas strongly offset by the high symmetry. The origin of high symmetry was investigated, and the mechanism of the symmetry breakdown was explained.