Path planning is the core problem of orchard fertilization robots during their operation. The traditional full-coverage job path planning algorithm has problems, such as being not smooth enough and having a large curvature fluctuation, that lead to unsteady running and low working efficiency of robot trajectory tracking. To solve the above problems, an improved A* path planning algorithm based on a multi-constraint Bessel curve is proposed. First, by improving the traditional A* algorithm, the orchard operation path can be fully covered by adding guide points. Second, according to the differential vehicle kinematics model of the orchard fertilization robot, the robot kinematics constraint is combined with a Bessel curve to smooth the turning path of the A* algorithm, and the global path meeting the driving requirements of the orchard fertilization robot is generated by comprehensively considering multiple constraints such as the minimum turning radius and continuous curvature. Finally, the pure tracking algorithm is used to carry out tracking experiments to verify the robot’s driving accuracy. The simulation and experimental results show that the maximum curvature of the planned trajectory is 0.67, which meets the autonomous operation requirements of the orchard fertilization robot. When tracking the linear path in the fertilization area, the average transverse deviation is 0.0157 m, and the maximum transverse deviation is 0.0457 m. When tracking the U-turn path, the average absolute transverse deviation is 0.1081 m, and the maximum transverse deviation is 0.1768 m, which meets the autonomous operation requirements of orchard fertilization robots.
With the development of pesticide substitution technology, ozonated water has been gradually applied in agricultural plant protection. This paper describes our development of an ecological plant protection unmanned aerial vehicle (UAV) that can produce and spray ozonated water while flying. Firstly, this paper carries out the design of the ozonated water system, including the selection of the ozone generator and the gas-liquid mixing method. Secondly, the conceptual design method of the ecological plant protection UAV is introduced, including total weight estimation, propulsion system selection, layout and structure design, battery modeling, center of gravity evaluation, and control system. Then, static analysis was computed in ANSYS Workbench on the UAV fuselage. Finally, the field test verified that the hovering time of the UAV could reach the design requirement of 10 min when it was fully loaded. The effective spraying width (with a height of 2 m and a speed of 3 m/s) is 5.25 m. The UAV was used to spray ozonated water with a concentration of 17 ppm continuously once a day; on day 7, the control effect could reach 76.4% and the reduction rate of the larvae population was 59.3%. Therefore, spraying ozonated water with a concentration of 17 ppm every day by using the ecological plant protection UAV can effectively control broccoli diamondback moth larvae and achieve the control effect of traditional pesticides (Chlorantraniliprole SC).
1 January 2019 in International Journal of Precision Agricultural Aviation
LiDAR placement and field of view selection play a role in detecting the relative position and pose of vehicles in relocation maps based on high-precision map automatic navigation. When the LiDAR field of view is obscured or the LiDAR position is misplaced, this can easily lead to loss of repositioning or low repositioning accuracy. In this paper, a method of LiDAR layout and field of view selection based on high-precision map normal distribution transformation (NDT) relocation is proposed to solve the problem of large NDT relocation error and position loss when the occlusion field of view is too large. To simulate the real placement environment and the LiDAR obstructed by obstacles, the ROI algorithm is used to cut LiDAR point clouds and to obtain LiDAR point cloud data of different sizes. The cut point cloud data is first downsampled and then relocated. The downsampling points for NDT relocation are recorded as valid matching points. The direction and angle settings of the LiDAR point cloud data are optimized using RMSE values and valid matching points. The results show that in the urban scene with complex road conditions, there are more front and rear matching points than left and right matching points within the unit angle. The more matching points of the NDT relocation algorithm there are, the higher the relocation accuracy. Increasing the front and rear LiDAR field of view prevents the loss of repositioning. The relocation accuracy can be improved by increasing the left and right LiDAR field of view.
31 August 2024 in INMATEH Agricultural Engineering
In order to solve the problems of low correlation between variable fertilizer application system and soil nutrient content detection and insufficient real-time performance, a variable fertilizer application system based on real-time soil nutrient content detection was developed. This paper describes the structure, working principle and design of key components of the soil information acquisition and fertilizer application system. It includes the simulation and analysis of fertilizer application using the discrete element method and the selection of curved blade fertilizer application discs. The system uses STM32F429IGT6 microcontroller and ROS higher-level computer for decision making. The device detects soil nutrients in real time, adjusts the fertilizer motor speed accordingly, and runs autonomously along the planned path. The decision coefficient R^2 between the fertilizer application rate and the speed of the fertilizer application wheel is not less than 0.97, and the relative error between the actual fertilizer application rate and the theoretical fertilizer application rate is up to 5.91%, with the maximum value of the coefficient of variation (CV) of 10.18%. The indoor bench test shows that the relative error between the actual fertilizer application rate and the target fertilizer application rate within a single operating grid is up to 6.2%, with the maximum value of CV being 6.64%. The field test in the orchard showed that the maximum relative error between the actual fertilizer application and the target fertilizer application in a single operation grid was 6.3%, and the maximum value of CV was 12.34%, and the fertilizer application was completed in the operation grid, which demonstrated that the device was able to realize real-time and accurate variable fertilizer application according to the soil nutrient information.
31 August 2024 in INMATEH Agricultural Engineering
The aim of this research is to address the issues of low precision in variable spraying within the existing farmland application system, whereby nozzles cannot be controlled independently and low pesticide utilisation is observed. A variable spraying system based on PTO protocol has been designed. The system comprises an STM32 microcontroller as the control core, including the host computer, multi-channel controller, electronic switch, and electromagnetic spray nozzle. The master control unit receives the spray amount set by the user and calculates the duty cycle of the corresponding nozzle, which is then sent to the multiplex controller in real time through CAN communication. The multiplex controller adjusts the on-off frequency and duty cycle of each electromagnetic nozzle in real time according to the duty cycle of the corresponding nozzle it receives, thus enabling the nozzles to be controlled independently. This study offers theoretical and technical support for the independent control of spray nozzles and the optimisation of pesticide utilisation for variable spray systems based on PTO protocols.