This study experimentally investigated bridge pier shape effect on the impact force induced by shock wave generated by a dam break, under four different reservoir water depths and dry downstream flow condition. The maximum force, its occurrence time, force intensity, and the impulse were criteria used to evaluate the performance of the bridge piers. Average and wave front celerities were investigated experimentally and numerically and were compared with existing equations in the literature. The time histories of the impact forces were measured using a load cell, and a two-dimensional numerical model was used to determine the shock wave celerities. At a reservoir water depth of 25 cm, the rectangular bridge pier recorded an impact force 2.68 times greater than that of the ogival pier, which had the smallest impact force, and the maximum force occurred 6.23 times earlier than in the case of the upstream facing ogival pier, which recorded the longest time to maximum force. The force intensity for the rectangular pier was approximately 1.8 times higher than that of the ogival bridge pier, which had the lowest force intensity across all studied water depths. It was found that a 2.5-fold increase in reservoir water depth led to an increase in up to 5.51 times the impact force for the rectangular pier.
1 March 2023 in Konya Journal of Engineering Sciences
Köprülerin yapısal güvenliği açısından oldukça önemli olan köprü ayaklarının tasarımının, hidrolik açıdan da analizi gerekmektedir. Köprü ayakları, akım alanını daraltarak köprü membaında kabarmalara ve beraberinde taşkınlara neden olabilmektedir. Dolayısıyla farklı akım koşullarında köprü ayaklarının etkisi altında oluşan su yüzü profillerinin ve kabarma miktarlarının deneysel ve sayısal çalışmalar ışığı altında en doğru şekilde belirlenmesi köprü hidrolik tasarımının önemli bir bölümünü oluşturmaktadır. Bu çalışmada, farklı enkesitlerdeki köprü ayaklarının ve verevlik açısının köprü etrafında oluşan su yüzü profili ve köprü membaındaki kabarma miktarı üzerindeki etkileri deneysel ve sayısal olarak araştırılmıştır. Deneysel çalışmalar Niğde Ömer Halisdemir Üniversitesi Mühendislik Fakültesi İnşaat Mühendisliği Bölümü Hidrolik Laboratuvarında bulunan ve boyutları 10x0.309x0.45 m olan deneysel kanal üzerinde yürütülmüştür. Yapılan deneysel çalışmalarda 4 farklı köprü ayağı tipi (kare, dairesel, kenarları yuvarlatılmış ve memba yüzü keskin kenarlı) ve 4 farklı verevlik açısı (00, 150, 300 ve 450) kullanılarak kanalda akım ölçümleri yapılmış ve ayrıca her bir deneye ait video kayıtları alınarak elde edilen görüntüler görüntü işleme tekniği yardımıyla sayısal verilere dönüştürülmüştür. Deneysel çalışmaların yanı sıra HEC-RAS yazılımı ve direk adım metodu kullanılarak sayısal modelleme çalışmaları da yapılmış, su yüzü profilleri ve kabarma miktarları karşılaştırma amaçlı elde edilmiştir. Elde olunan sayısal sonuçlar karşılaştırılmış, benzer problemlerde HEC-RAS yazılımın kullanılabilirliği ile görüntü işleme tekniğinin uygulanabilirliği ile ilgili çıkarımlara yer verilmiştir.
This experimental study focused on the measurement and analysis of the impact force caused by a tsunami bore on a coastal structure. The bore wave was produced by a dam break mechanism. The water depth in the reservoir and the location of the coastal structures were varied to simulate different impact scenarios. The time history of the force resulting from the impact of the bore wave on the coastal structure was measured. The propagation of the bore wave along the flume was recorded and the video recordings were converted into digital data using an image-processing technique in order to determine the flow depth variations with time. The hydrostatic forces and the corresponding depth and time-averaged hydrodynamic forces as well as the maximum hydrodynamic forces were acquired for each scenario. The ratio of hydrodynamic to hydrostatic forces were obtained, and it was observed that the calculated averaged ratio was within the recommended design ratio. The results indicate that an increase in the reservoir level caused an increase in the magnitude and intensity of the impact forces, however, the relationship was non-linear. Moreover, it was found that the location of the structure did not play a significant role on the intensity of the impact forces.
This study numerically investigated the influence of downstream bed slopes of 0°, 5°, 10°, and 15° and bridge pier positions of 1.1 and 1.3 m on the impact force induced by a tsunami surge wave. Square, circular, and ogival bridge pier geometries were studied to evaluate the influence of geometry. The numerical model used in the study was validated against experimental benchmarks in the literature, and the pressure and impact force time histories were analyzed. The results confirm the suitability of the model for simulating this surge–structure interaction. The results show that the impact forces are significantly influenced by pier geometry. The square geometry recorded a maximum horizontal impact force of 1.73 and 3.32 times more than those for the circular and ogival geometries, respectively. The result further shows that increasing downstream bed slope causes a reduction in the recorded impact forces. The reduction is influenced by the pier geometry, with a maximum reduction of 23% for the square, 32% for the circular, and 38% for the ogival pier recorded as the downstream bed slope increases from 0° to 15°. The circular and ogival pier cases were found to have mitigated flow stagnation and pressure amplification relatively better than the square pier geometry. Slope-dependent reduction factors were proposed for possible incorporation into design guidelines. This study provides practical frameworks for design purposes.
This study investigates the interaction between tsunami-like surge waves and structural mitigation measures using a combination of laboratory experiments and numerical simulations. The main focus is on the transient fluid–structure interaction processes governing surge transformation, momentum redistribution, and the mitigation of impact loads. Experiments were conducted in a horizontal rectangular flume (10 × 0.309 × 0.45 m3) under dry bed downstream conditions with varying initial reservoir water levels to simulate highly unsteady surge propagation caused by a dam-break mechanism. The flow depths were obtained using an image-processing technique, and the horizontal impact forces on the downstream structures were measured using a load cell system. The performance of the mitigation structures was evaluated with multiple hydrodynamic and loading parameters, including impact time, maximum water depth, maximum horizontal force, force concentration, and impulse. Rather than a single performance metric based on peak force reduction, this work shows that mitigation structures fundamentally alter the time-dependent nature of surge loading by redistributing the momentum transfer and increasing the duration of the impact. The results also indicate that the structural geometry, size, and orientation have a significant effect on the deformation of the surge front, the generation of localized turbulence, and the flow deceleration processes and, consequently, the instantaneous and cumulative loading characteristics experienced by the downstream structures.