The purpose of this experimental work was to investigate the role of the leading-edge wavy shape technique on the performance of small-scale HAWT fixed-pitch rotor blades operating under off-design conditions. Geometric parameters such as amplitude and wavelength were considered design variables to generate five different wavy shape blade models in order to increase the aerodynamic performance of the rotor with a diameter of 280 mm. A dedicated airfoil type S822 for small wind turbine application from the NREL Airfoil Family was chosen to fulfil both the aerodynamic and structural aspects of the blades. Rotor models were tested in a wind tunnel for different wind speeds while maintaining constant rotational speed to provide the blade-tip chord Reynolds number of 4.7 × 104. The corrected tunnel data, in terms of power coefficients and tip-speed ratios, were compared first with the literature to validate the experimental approach, and then among themselves. It was observed that for minimal sizes of tubercles, the performance of the rotor increases by about 40% compared to the RB1 baseline rotor model for a low tip-speed ratio. Conversely, for the maximum size of the tubercles, there is a marked decrease of about 51% of the rotor performance for a moderate tip-speed ratio compared to the RB1 rotor model. Among these models, specifically, the RB2 rotor model with the smallest values of amplitude and wavelength provides a 2.8% higher peak power coefficient compared to the RB1 rotor model, and at the same time preserves higher performance values for a broad range of tip-speed ratios.
This study experimentally investigated bridge pier shape effect on the impact force induced by shock wave generated by a dam break, under four different reservoir water depths and dry downstream flow condition. The maximum force, its occurrence time, force intensity, and the impulse were criteria used to evaluate the performance of the bridge piers. Average and wave front celerities were investigated experimentally and numerically and were compared with existing equations in the literature. The time histories of the impact forces were measured using a load cell, and a two-dimensional numerical model was used to determine the shock wave celerities. At a reservoir water depth of 25 cm, the rectangular bridge pier recorded an impact force 2.68 times greater than that of the ogival pier, which had the smallest impact force, and the maximum force occurred 6.23 times earlier than in the case of the upstream facing ogival pier, which recorded the longest time to maximum force. The force intensity for the rectangular pier was approximately 1.8 times higher than that of the ogival bridge pier, which had the lowest force intensity across all studied water depths. It was found that a 2.5-fold increase in reservoir water depth led to an increase in up to 5.51 times the impact force for the rectangular pier.
The aim of this research work was to explore how modifying the design of small-scale HAWT rotor blades through the backward-facing step technique affects their efficiency under varying wind speeds. The study involved altering step parameters such as location, length, and depth to create four distinct stepped blade shapes and enhance the aerodynamic performance of a rotor with a diameter of 280 mm. A specific blade profile, NREL S822, was selected to meet both aerodynamic and structural criteria. The rotor models were examined at a Reynolds number of 4.7 × 104 for wind speeds between 8.5 and 15.5 m/s and tip-speed ratios between 2 and 5. The experimental results indicated that for certain geometric step parameter values, the efficiency of the rotor model (B3) increased by approximately 47% compared to the base model (B1), particularly for tip-speed ratios lower than around 3.2. However, beyond this point, the rotor efficiency dropped significantly, reaching approximately 60% in one case. Additionally, a hybrid rotor model (B6) was generated by combining the shape of the rotor model (B4) with the most efficient rotor model from the literature, generated using the leading-edge wavy shape technique. This hybrid rotor model enhanced rotor efficiency for specific values of tip-speed ratio and also ensured its smoother operation. Overall, the rotor model (B2), distinguished by smaller step parameter values and a shift as well as broadening of the power coefficient curve towards lower tip-speed ratio values, exhibited a higher peak power coefficient, approximately 1.4% greater than the base rotor (B1). This increase occurred at a lower tip-speed ratio, allowing the rotor to operate with higher efficiency across a broader range of tip-speed ratios.
In this study, passive and active flow control methods were used together to manipulate the flow around a circular cylinder. The experiments were conducted in a wind tunnel for the Reynolds number range of 4000 and 10000 based on the diameter of the circular cylinder (D). A splitter plate was used as passive flow control device and its length was chosen to be about 3.75D. Plasma actuators were placed on the circular cylinder at a position of ±90° as an active flow control device. Combining the active and passive flow control methods, a greater reduction of the drag coefficient was achieved compared to that of the cases when using these methods separately. For Reynolds numbers of 5000 and 10000, the hybrid method gives a reduction in drag of 48% and 45%, respectively. The velocity measurements were carried out by using the hot-wire anemometry and velocity profiles were obtained in the wake region. The flow was visualized by using a smoke wire method. The results revealed that the wake region of the circular cylinder with plasma actuator and splitter plate has a narrower width than the plain cylinder and with splitter plate. Also, it can be seen from spectral analysis that the vortex shedding frequency was suppressed significantly by usage of the hybrid flow control method was used. Bu çalışmada, pasif ve aktif akış kontrol metotları birlikte kullanılarak bir dairesel silindir etrafındaki akış manipüle edilmiştir. Deneyler dairesel silindirin çapına bağlı (D) Reynolds sayısının 4000 ve 10000 olduğu değerlerde rüzgâr tünelinde gerçekleştirilmiştir. Pasif akış kontrol metodu olarak 3.75D uzunluğa sahip ayırıcı plaka seçilmiştir. Aktif akış kontrol metodu elemanı olarak ise plazma aktüatörler seçilmiştir ve dairesel silindirin ±90° konumuna yerleştirilmiştir. Aktif ve pasif akış kontrol yöntemleri birlikte kullanılarak, bu yöntemleri ayrı ayrı kullanılmasına göre daha büyük bir azalma elde edilmiştir. Reynolds sayısının 5000 ve 10000 olduğu değerler için hibrit yöntem, sürükleme katsayısında sırasıyla %48 ve %45 azalma sağlamıştır. Hız ölçümleri kızgın tel anemometresi kullanılarak yapılmıştır ve iz bölgesindeki hız profilleri elde edilmiştir. Akış, duman-tel yöntemi kullanılarak görselleştirilmiştir. Plazma aktüatörlü ve ayırıcı plakalı dairesel silindirin iz bölgesinin sade silindire ve ayırıcı plaka kullanılan silindirin iz bölgesine kıyasla daha dar bir genişliğe sahip olduğu sonuçlarla ortaya koyulmuştur. Ayrıca, spektral analizden, hibrit akış kontrol yöntemi kullanılarak girdap kopma frekansının önemli ölçüde baskılandığı gözlemlenmiştir.
This experimental study focused on the measurement and analysis of the impact force caused by a tsunami bore on a coastal structure. The bore wave was produced by a dam break mechanism. The water depth in the reservoir and the location of the coastal structures were varied to simulate different impact scenarios. The time history of the force resulting from the impact of the bore wave on the coastal structure was measured. The propagation of the bore wave along the flume was recorded and the video recordings were converted into digital data using an image-processing technique in order to determine the flow depth variations with time. The hydrostatic forces and the corresponding depth and time-averaged hydrodynamic forces as well as the maximum hydrodynamic forces were acquired for each scenario. The ratio of hydrodynamic to hydrostatic forces were obtained, and it was observed that the calculated averaged ratio was within the recommended design ratio. The results indicate that an increase in the reservoir level caused an increase in the magnitude and intensity of the impact forces, however, the relationship was non-linear. Moreover, it was found that the location of the structure did not play a significant role on the intensity of the impact forces.