Micro gas turbine (MGT) technology is evolving toward a large variety of novel applications, such as weak gas electrification, inverted Brayton cycles, and fuel cell hybrid cycles; however, many of these systems show very different dynamic behaviors compared to conventional MGTs. In addition, some applications impose more stringent requirements on transient maneuvers, e.g., to limit temperature and pressure gradients in a fuel cell hybrid cycle. Besides providing operational safety, optimizing system dynamics to meet the variable power demand of modern energy markets is also of increasing significance. Numerical cycle simulation programs are crucial tools to analyze these dynamics without endangering the machines, and to meet the challenges of automatic control design. For these tasks, complete cycle simulations of transient maneuvers lasting several minutes need to be calculated. Moreover, sensitivity analysis and optimization of dynamic properties like automatic control systems require many simulation runs. To perform these calculations in an acceptable timeframe, simplified component models based on lumped volume or one-dimensional discretization schemes are necessary. The accuracy of these models can be further improved by parameter identification, as most novel applications are modifications of well-known MGT systems and rely on proven, characterized components. This paper introduces a modular in-house simulation tool written in fortran to simulate the dynamic behavior of conventional and novel gas turbine cycles. Thermodynamics, gas composition, heat transfer to the casing and surroundings, shaft rotation and control system dynamics as well as mass and heat storage are simulated together to account for their interactions. While the presented models preserve a high level of detail, they also enable calculation speeds up to five times faster than real-time. The simulation tool is explained in detail, including a description of all component models, coupling of the elements and the ODE solver. Finally, validation results of the simulator based on measurement data from the DLR Turbec T100 recuperated MGT test rig are presented, including cold start-up and shutdown maneuvers.
19 August 2013 in Journal of Engineering for Gas Turbines and Power
Microgas turbine (MGT) based combined heat and power (CHP) units provide a highly efficient, low-pollutant technology to supply heat and electrical power from fossil and renewable energy sources; however, pressurized MGT systems in an electrical power range from 1 to 5 utilize very small turbocharger components. These components suffer from higher losses, like seal and tip leakages, resulting in a reduced electrical efficiency. This drawback is avoided by an inverted Brayton cycle (IBC) based system. In an IBC hot gas is produced in a combustion chamber at atmospheric pressure. Subsequently, the exhaust gas is expanded in a turbine from an atmospheric to a subatmospheric pressure level. In order to increase electrical efficiency, heat from the turbine exhaust gas is recuperated to the combustion air. After recuperation, the gas is compressed to atmospheric pressure and is discharged from the cycle. To decrease the power demand of the compressor, and thereby increasing the electrical cycle efficiency, it is crucial to further extract residual thermal power from the gas before compression. Coolant flows provided by heating applications can use this heat supply combined with heat from the discharged exhaust gas. The low pressure levels of the IBC result in high volumetric gas flows, enabling the use of large, highly efficient turbocharger components. Because of this efficiency benefit and the described cooling demand, micro-CHP applications provide an ideal field for utilization of the IBC. To further increase the total efficiency, discharged exhaust gas can be partially recirculated to the air inlet of the cycle. In the present paper a steady state analysis of an IBC with exhaust gas recirculation (EGR) is shown, and compared to the performance of a conventional Brayton cycle with equivalent component properties. Using EGR, it could be found that the sensitivity of the electrical cycle efficiency to the coolant temperature further increases. The sequent discussion focuses on the trade-off between total efficiency and electrical efficiency, depending on coolant temperature and EGR rate. The results show that EGR can increase the total efficiency by 10% to 15% points, while electrical efficiency decreases by 0.5% to 1% point. If the coolant temperature is below 35 °C, condensation of water vapor in the exhaust gas leads to a further increase of heat recovery efficiency. A validated in-house simulation tool based on turbocharger maps has been used for the calculations.
13 January 2021 in Journal of Engineering for Gas Turbines and Power
Recognizing the attention currently devoted to the environmental impact of aviation, this three-part publication series introduces two new aircraft propulsion concepts for the timeframe beyond 2030. The first part focuses on the novel steam injecting and recovering aero engine concept. In the second part, the free-piston composite cycle engine (FP-CCE) concept is presented. Complementary to the two technical publications, this third part describes the cooperative project, which was initiated by an interdisciplinary consortium, aiming at the demonstration and the proof-of-concept of both aforementioned aero engine concepts. At the beginning of the project, simulations on propulsion, aircraft system, and test bench level will be conducted. On this basis, preliminary tests and fundamental experiments are planned in order to establish a solid basis for the demonstration. Finally, a system demonstration will be carried out at the laboratory level. Thus, the project allows for a final judgment on both the feasibility of the new concepts and the attainability of the requirements for future aircraft propulsion systems.
29 November 2018 in Journal of Engineering for Gas Turbines and Power
Steady-state simulation is an important method to investigate thermodynamic processes. This is especially true for innovative micro gas turbine (MGT)-based cycles as the complexity of such systems grows. Therefore, steady-state simulation tools are required that ensure large flexibility and computation robustness. As the increased system complexity result often in more extensive parameter studies also a fast computation speed is required. While a number of steady-state simulation tools for MGT-based systems are described and applied in literature, the solving process of such tools is rarely explained. However, this solving process is crucial to achieve a robust and fast computation within a physically meaningful range. Therefore, a new solver routine for a steady-state simulation tool developed at the DLR Institute of Combustion Technology is presented in detail in this paper. The solver routine is based on Broyden's method. It considers boundaries during the solving process to maintain a physically and technically meaningful solution process. Supplementary methods are implemented and described which improve the computation robustness and speed. Furthermore, some features of the resulting steady-state simulation tool are presented. Exemplary applications of a hybrid power plant (HyPP), an inverted Brayton cycle (IBC), and an aircraft auxiliary power unit (APU) show the capabilities of the presented solver routine and the steady-state simulation tool. It is shown that the new solver routine is superior to the standard Simulink algebraic solver in terms of system evaluation and robustness for the given applications.
To further increase efficiency and to significantly reduce climate impact in the aviation sector, new propulsion concepts must be developed. As full electrification in mid- and long-range aviation is impractical due to the low gravimetric energy density of batteries, new approaches must be developed. Therefore, the so-called hybrid electric ground demonstrator (HeBo), equipped with a Rolls Royce M250-C20B gas turbine is set up. The test rig serves as a development platform for various new gas turbine-based propulsion concepts for aviation, such as hybrid electric concepts or a novel cycle concept with steam injection to the combustor, which are described in this paper. The main focus of the work is on the experimental setup and the commissioning of the baseline test rig. This will place the test rig in the context of current research activities and serve as reference for subsequent research results.