Amit Kumar

Dr. Amit Kumar

Central Electronics Engineering Research Institute, Pilāni, India

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 May 2013 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
DBDeepak Bansal
Deepak Bansal
AKAmit Kumar
Amit Kumar
ASAkshdeep Sharma
Akshdeep Sharma
PKPrem Kumar
Prem Kumar
KRK. J. Rangra
K. J. Rangra

8 December 2016 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Closed access
PDF file
DBDeepak Bansal
Deepak Bansal
ABAnuroop Bajpai
Anuroop Bajpai
PKPrem Kumar
Prem Kumar
MKManinder Kaur
Maninder Kaur
AKAmit Kumar
Amit Kumar
KRKamaljit Rangra
Kamaljit Rangra
Variation in actuation voltage for RF MEMS switches is observed as a result of stress-generated buckling of MEMS structures. Large voltage driven RF-MEMS switches are a major concern in space bound communication applications. In this paper, we propose a low voltage driven RF MEMS capacitive switch with the introduction of perforations and reinforcement. The performance of the fabricated switch is compared with conventional capacitive RF MEMS switches. The pull-in voltage of the switch is reduced from 70 V to 16.2 V and the magnitude of deformation is reduced from 8 µ m to 1 µ m. The design of the reinforcement frame enhances the structural stiffness by 46 % without affecting the high frequency response of the switch. The measured isolation and insertion loss of the reinforced switch is more than 20 dB and 0.4 dB over the X band range.

15 August 2019 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
DBDeepak Bansal
Deepak Bansal
ABAnuroop Bajpai
Anuroop Bajpai
KMKhushbu Mehta
Khushbu Mehta
PKPrem Kumar
Prem Kumar
AKAmit Kumar
Amit Kumar
RF MEMS ohmic switches are prone to stiction and contact degradation. In literature, bumps are made at the contact area to reduce stiction with additional fabrication steps. In this article, ohmic switch based on cantilever configuration is developed without using any additional step. The switch structure is modified to improve its mechanical parameters, such as pull-in voltage and switching speed. The measured switching time of the switch is 1.8 μs. A footprint of the developed single pole single throw (SPST) switch is 0.9 mm². The insertion loss and isolation of the SPST switch are better than 0.8 and 20 dB, respectively. The switch has a wide bandwidth of 10 GHz (dc to 10 GHz). The switch has completed 725 million hot cycles at 1-dBm power.

20 June 2014 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
DBDeepak Bansal
Deepak Bansal
AKAmit Kumar
Amit Kumar
ASAkshdeep Sharma
Akshdeep Sharma
KRK. J. Rangra
K. J. Rangra

1 January 2014 in Journal of Micro/Nanolithography, MEMS, and MOEMS
Verified
Journal Article
Closed access
PDF file
ASAkshdeep Sharma
Akshdeep Sharma
PJPrachi Jhanwar
Prachi Jhanwar
DBDeepak Bansal
Deepak Bansal
AKAmit Kumar
Amit Kumar
MKManinder Kaur
Maninder Kaur
KRKamaljit Rangra
Kamaljit Rangra
A comparison of dry and wet release methods for surface micromachining of metallic structures, such as RF MEMS switches, test structures, bridges, and cantilevers is presented. The dry release process is optimized by varying the concentration of O2 and CF4 plasma and RF power. The plasma ashing of the sacrificial layer typically results in damage to metallic structures or stress-related deformation due to rise in temperature (>80°C). A wet release process using critical point drying (CPD) has been investigated to realize gold-electroplated structures with reduced residual stress. The CPD, being a low-temperature (31.1°C) process, is more suitable for compliant structures without any deformation.

1 January 2020 in Microelectronic Engineering
Verified
Journal Article
Closed access
AKAmit Kumar
Amit Kumar
ASAshudeep
Ashudeep
DBDeepak Bansal
Deepak Bansal
PKPrem Kumar
Prem Kumar
ANAnuroop
Anuroop
KRKamaljit Rangra
Kamaljit Rangra