Deepak Bansal

Deepak Bansal

Auto-generated profile, based on publicly available information

Deepak Bansal

CSIR-Central Electronics Engineering Research Institute

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 May 2013 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
DBDeepak Bansal
Deepak Bansal
AKAmit Kumar
Amit Kumar
ASAkshdeep Sharma
Akshdeep Sharma
PKPrem Kumar
Prem Kumar
KRK. J. Rangra
K. J. Rangra

8 December 2016 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Closed access
PDF file
DBDeepak Bansal
Deepak Bansal
ABAnuroop Bajpai
Anuroop Bajpai
PKPrem Kumar
Prem Kumar
MKManinder Kaur
Maninder Kaur
AKAmit Kumar
Amit Kumar
KRKamaljit Rangra
Kamaljit Rangra
Variation in actuation voltage for RF MEMS switches is observed as a result of stress-generated buckling of MEMS structures. Large voltage driven RF-MEMS switches are a major concern in space bound communication applications. In this paper, we propose a low voltage driven RF MEMS capacitive switch with the introduction of perforations and reinforcement. The performance of the fabricated switch is compared with conventional capacitive RF MEMS switches. The pull-in voltage of the switch is reduced from 70 V to 16.2 V and the magnitude of deformation is reduced from 8 µ m to 1 µ m. The design of the reinforcement frame enhances the structural stiffness by 46 % without affecting the high frequency response of the switch. The measured isolation and insertion loss of the reinforced switch is more than 20 dB and 0.4 dB over the X band range.

31 October 2018
Verified
Conference Paper
Open access
PDF file
ARArjun Roy
Arjun Roy
DBDeepak Bansal
Deepak Bansal
DBDavid Brumley
David Brumley
HCHarish Kumar Chandrappa
Harish Kumar Chandrappa
PSParag Sharma
Parag Sharma
ASAlex C. Snoeren
Alex C. Snoeren

1 September 2019 in Superlattices and Microstructures
Verified
Journal Article
Closed access
MAMahesh Angira
Mahesh Angira
DBDeepak Bansal
Deepak Bansal
PKPrem Kumar
Prem Kumar
KMKhusbu Mehta
Khusbu Mehta
KRKamaljit Rangra
Kamaljit Rangra

15 August 2019 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
DBDeepak Bansal
Deepak Bansal
ABAnuroop Bajpai
Anuroop Bajpai
KMKhushbu Mehta
Khushbu Mehta
PKPrem Kumar
Prem Kumar
AKAmit Kumar
Amit Kumar
RF MEMS ohmic switches are prone to stiction and contact degradation. In literature, bumps are made at the contact area to reduce stiction with additional fabrication steps. In this article, ohmic switch based on cantilever configuration is developed without using any additional step. The switch structure is modified to improve its mechanical parameters, such as pull-in voltage and switching speed. The measured switching time of the switch is 1.8 μs. A footprint of the developed single pole single throw (SPST) switch is 0.9 mm². The insertion loss and isolation of the SPST switch are better than 0.8 and 20 dB, respectively. The switch has a wide bandwidth of 10 GHz (dc to 10 GHz). The switch has completed 725 million hot cycles at 1-dBm power.

8 April 2020 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
DBDeepak Bansal
Deepak Bansal
ABAnuroop Bajpai
Anuroop Bajpai
PKPrem Kumar
Prem Kumar
MKManinder Kaur
Maninder Kaur
AKAmit Kumar
Amit Kumar
RF MEMS switches are well known to exhibit performance superior to solid-state devices. However, electromechanical issues, such as repeatability and higher pull-in voltage, are a matter of concern. MEMS switches generally consist of metallic beams which curl up or down based on stresses in the structure. Stress-induced curling-up phenomenon, in such structures, increases the gap between the actuating electrode and the freely suspended metallic structure which in turn increases the pull-in voltage. This article focuses on simulations and curve fitting to analyze the effect of stress on pull-in voltage. The pull-in voltage of the switch is proportional to stress, and accordingly, its dependence on in-built stress and Young's modulus is analyzed. In addition to mechanical analysis, RF response of the single pole double throw (SPDT) switch is discussed as a case study. Measured stress and pull-in voltage of the SPDT switch is 50 MPa and 16 V. In the presence of stress, the curled-up cantilever switch shows measured isolation better than 31 dB for dc to 10-GHz range.