Theo Dingemans

Dr. Theo Dingemans

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 November 2017 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
MPMichiel L. Petrus
Michiel L. Petrus
AMArif Music
Arif Music
ACAnna C. Closs
Anna C. Closs
JBJohan C. Bijleveld
Johan C. Bijleveld
MSMaximilian T. Sirtl
Maximilian T. Sirtl
PDPablo Docampo
Pablo Docampo
The current state-of-the-art hole transporting materials (HTM) for perovskite solar cells are generally synthesized via cross-coupling reactions that require expensive catalysts, inert reaction conditions and extensive product purification, resulting in high costs and therefore limiting large-scale commercialisation. Here we describe a series of HTMs prepared via simple and clean Schiff-base condensation chemistry with an estimated material cost in the range of 4–54 $ per g. The optoelectronic and thermal properties of the materials are linked to the changes in the chemical structure of the HTMs, which allow us to extract design rules for new materials, supported by density functional theory calculations. Charge transport measurements show hole mobilities in the range of 10−5 to 10−7 cm2 V−1 s−1. Upon addition of LiTFSI the HTMs can be oxidized, resulting in a large increase in the conductivity of the hole transporting layer (HTL). When employed as HTL in perovskite solar cells, power conversion efficiencies close to those of spiro-OMeTAD are obtained. In particular, devices prepared with Diazo-OMeTPA show a higher open-circuit voltage. Furthermore, we show that azomethine-based HTMs can act as effective moisture barriers, resulting in a significant increase in the stability of the underlying perovskite film. We assign the improved properties to the presence of a dipole in our molecules which promotes a close molecular packing and thus leads to a high density of the as-formed HTM films, preventing the ingress of water. This work shows that HTMs prepared via condensation chemistry are not only a low-cost alternative to spiro-OMeTAD, but also act as a functional barrier against moisture-induced degradation in perovskite solar cells.

9 May 2018 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
MLMing Li
Ming Li
QGQingbao Guan
Qingbao Guan
TDTheo Dingemans
Theo Dingemans
We have explored semi-crystalline poly(decamethylene terephthalamide) (PA 10T) based thermosets as single-component high-temperature (> 200 °C) shape memory polymers (SMPs). The PA 10T thermosets were prepared from reactive thermoplastic precursors. Reactive phenylethynyl (PE) functionalities were either attached at the chain termini or placed as side-groups along the polymer main-chain. The shape fixation and recovery performance of the thermoset films were investigated using a rheometer in torsion mode. By controlling the Mn of the reactive oligomers, or the PE concentration of the PE side-group functionalized copolyamides, we were able to design dual-shape memory PA 10T thermosets with a broad recovery temperature range of 227-285 °C. The thermosets based on the 1000 g·mol-1 reactive PE precursor and the copolyamide with 15 mol% PE side-groups show the highest fixation rate (99%) and recovery rate (≥90%). High temperature triple-shape memory behavior can be achieved as well when we use the melt transition (Tm ≥ 200 °C) and the glass transition (Tg = ~125 °C) as the two switches. The recovery rate of the two recovery steps are highly dependent on the crystallinity of the thermosets and vary within a wide range of 74%-139% and 40-82% for the two steps, respectively. Reversible shape-memory events could also be demonstrated when we perform a forward and backward deformation in a triple shape-memory cycle. We also studied the angular recovery velocity as a function of temperature, which provides a thermokinematic picture of the shape recovery process and helps to program for desired shape memory behavior.

11 February 2020 in Nature Communications
Verified
Journal Article
Open access
PDF file
MHMaruti Hegde
Maruti Hegde
LYLin Yang
Lin Yang
Francesco VitaFrancesco Vita
Francesco Vita
RFRyan J. Fox
Ryan J. Fox
RWRenee van de Watering
Renee van de Watering
TDTheo Dingemans
Theo Dingemans
Combining polymers with small amounts of stiff carbon-based nanofillers such as graphene or graphene oxide is expected to yield low-density nanocomposites with exceptional mechanical properties. However, such nanocomposites have remained elusive because of incompatibilities between fillers and polymers that are further compounded by processing difficulties. Here we report a water-based process to obtain highly reinforced nanocomposite films by simple mixing of two liquid crystalline solutions: a colloidal nematic phase comprised of graphene oxide platelets and a nematic phase formed by a rod-like high-performance aramid. Upon drying the resulting hybrid biaxial nematic phase, we obtain robust, structural nanocomposites reinforced with graphene oxide.

1 August 2014 in Polymer
Verified
Journal Article
Closed access
MHMaruti Hegde
Maruti Hegde
ULUgo Lafont
Ugo Lafont
BNBen Norder
Ben Norder
ESEdward T Samulski
Edward T Samulski
MRMichael Rubinstein
Michael Rubinstein
TDTheo Dingemans
Theo Dingemans

11 September 2019 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
RFRyan J. Fox
Ryan J. Fox
DYDeyang Yu
Deyang Yu
MHMaruti Hegde
Maruti Hegde
AKAmar S. Kumbhar
Amar S. Kumbhar
LMLouis A. Madsen
Louis A. Madsen
TDTheo Dingemans
Theo Dingemans

28 June 2024 in PRX Energy
Verified
Journal Article
Open access
PDF file
HJHaoyang Jiao
Haoyang Jiao
MHMaruti Hegde
Maruti Hegde
NLNengxu Li
Nengxu Li
MOMichael Owen-Bellini
Michael Owen-Bellini
LSLaura Schelhas
Laura Schelhas
JHJinsong Huang
Jinsong Huang
The development of perovskite solar cells (PSCs) has ushered in a new era of solar technology, characterized by its exceptional efficiency and cost-effective production. However, the soft and fragile nature of perovskites makes module encapsulation challenging. Polyolefin elastomers (POEs) have been reported to be promising encapsulants for perovskite modules. However, little research exists on identifying criteria among different types of POEs as encapsulants. Here, two POEs with different morphologies were compared as encapsulants. The first POE crystallizes during encapsulation (crystal content ∼40%), and the resulting shrinkage or warpage leads to delamination, causing minimodule failure. In contrast, perovskite minimodules encapsulated with a mostly amorphous POE exhibited better reliability and reproducibility. The best perovskite minimodules passed the thermal cycling test for 240 cycles between −40 and 85 °C and the damp heat test for 1419 h, according to the IEC 61215 standard. This study highlights the importance of the morphology of encapsulants in achieving high-quality encapsulation. Published by the American Physical Society 2024