Amar Dhoj Malla

Dr. Amar Dhoj Malla

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 July 2025 in npj Materials Degradation
Verified
Journal Article
Open access
PDF file
AMAmar Dhoj Malla
Amar Dhoj Malla
GWG. Williams
G. Williams
DBD. A. Britton
D. A. Britton
FGF. E. Goodwin
F. E. Goodwin
ACAna P. Domingos Cardoso
Ana P. Domingos Cardoso
JSJ. H. Sullivan
J. H. Sullivan
Systematic investigations into the individual effects of increasing alloying additions of Mg and Al on the corrosion mechanisms of Zn-Mg-Al coatings have demonstrated that microstructural phases and their surface distribution determine the anodic and cathodic behaviour of the coating. Increasing either Al and/or Mg from 1 to 3 wt.% improved the surface corrosion performance of the coating, with a greater effect observed for Al additions due to anodic deactivation. Mg additions led to cathodic deactivation due to a significant reduction in Zn dendrites at the surface. The corrosion rate was minimised by maximising the ternary eutectic area fraction at the coating surface. A 52% and 32% decrease in SVET-derived metal loss is achieved at 3 wt.% increase in Al and Mg, respectively.

7 June 2024 in npj Materials Degradation
Verified
Journal Article
Open access
PDF file
DBDaniel A. Britton
Daniel A. Britton
DPDavid Penney
David Penney
AMAmar Dhoj Malla
Amar Dhoj Malla
SMShahin Mehraban
Shahin Mehraban
JSJames Sullivan
James Sullivan
CCClive Challinor
Clive Challinor
Microscopy, electrochemical techniques and mechanical testing are used to investigate the effect of varying antimony additions (0.45–1.8 wt%) on the microstructure and corrosion properties of zinc-magnesium-aluminium coating alloys. Samples were produced by splat casting to produce high cooling rates similar to those seen in a continuous galvanising line. X-Ray Microscopy reveals that the Sb additions produce disk-shaped Mg3Sb2 intermetallics, subsequently reducing or eliminating the MgZn2 eutectic. Electrochemical testing in 1 wt% NaCl shows that the Mg3Sb2 phase is cathodic with respect to the bulk alloy with slower oxygen reduction kinetics. The decrease in eutectic content leads to less intense anodic activity. The combined effect is anodic and cathodic deactivation, which leads to a 43% reduction in corrosion rate as measured through LPR compared to the base alloy. This work shows that quaternary additions to ZMA coating alloys can be a potential route to improved corrosion resistance for galvanic protection.

29 July 2024 in npj Materials Degradation
Verified
Journal Article
Open access
PDF file
AMAmar Dhoj Malla
Amar Dhoj Malla
JSJ. H. Sullivan
J. H. Sullivan
DPD. J. Penney
D. J. Penney
MGM. Goldsworthy
M. Goldsworthy
DBD. Britton
D. Britton
ACA. P. Cardoso
A. P. Cardoso
Time-lapse Microscopy, scanning vibrating electrode technique and potentiodynamic methods were used to study the influence of increasing coating weight (80–310 gm–2) on microstructure, cut-edge and surface corrosion of Zn-Mg-Al coatings in 0.17 M NaCl. Cut-edge corrosion was similar for all coatings due to the oxygen reduction reaction becoming diffusion-limited. A 64% reduction in surface corrosion was observed for high coating weights through increases in eutectic volume fraction. Spatial and temporal corrosion mechanisms were controlled by microstructural morphological differences as coating weight varied. 80 g.m–2 coatings demonstrated lateral anodic spreading potentially reducing coating penetration rates despite their higher surface corrosion rate.

16 July 2024 in Metals
Verified
Journal Article
Open access
PDF file
AMAmar Dhoj Malla
Amar Dhoj Malla
JSJames Henley Sullivan
James Henley Sullivan
DPDavid Penney
David Penney
ESElizabeth Sackett
Elizabeth Sackett
RLRobert J Lancaster
Robert J Lancaster
PBPeter Barker
Peter Barker
In this investigation, 0.19–1.8 wt.% of Ge was introduced into a ternary Zn-Mg-Al alloy. The introduction of Ge had a significant impact on the microstructure, leading to the formation of Mg2Ge. The area fraction of the eutectic phase diminished with increasing Ge additions. Small-scale test techniques were utilised to evaluate the mechanical properties due to the changes in microstructure. Zn-Mg-Al alloys were found to be inherently harder compared to standard hot-dip Zn-containing 0.2 wt.% Al. The hardness and strength of the Zn-Mg-Al alloys decreased with the increase in Ge additions.

4 May 2026 in npj Materials Degradation
Verified
Journal Article
Open access
PDF file
AMAmar Dhoj Malla
Amar Dhoj Malla
DPD. J. Penney
D. J. Penney
GWG. Williams
G. Williams
FGF. E. Goodwin
F. E. Goodwin
ACAna P. Domingos Cardoso
Ana P. Domingos Cardoso
JSJ. H. Sullivan
J. H. Sullivan
Zn-Mg-Al coatings (ZMA) on steel can provide enhanced corrosion resistance compared to zinc coating (GI) and are often used in applications that require shaping processes. This study investigates the effect of deformation-induced cracking on the corrosion of ZMA coatings of different weights (310 and 80 g m-2) benchmarked against GI. Cracks were more prevalent and of greater depth in ZMA coatings due to the presence of MgZn2 in the eutectic. ZMA with 310 g m-2 weight (ZMA310), exhibited a ~ 3 times greater crack area than 80 g m-2 weight (ZMA80) through an increased eutectic volume fraction. This caused an increase in corrosion rate of 3.8 times for ZMA310 relative to its undeformed condition over 24 h, with increases between 1.5 and 1.7 times for ZMA80 and GI. Two phenomena cause this increase: deformation-accelerated corrosion due to differential aeration-induced anodic activation in non-through-coating cracks, and cathodic activation in through-coating cracks resulting from galvanic coupling with the steel.