Zinc oxide arouses considerable interest since it has many applications—in microelectronics, environmental decontaminations, biomedicine, photocatalysis, corrosion, etc. The present investigation describes the green synthesis of nanosized ZnO particles using a low-cost, ecologically friendly approach compared to the classical methods, which are aimed at limiting their harmful effects on the environment. In this study, ZnO nanoparticles were prepared using an extract of Mentha arvensis (MA) leaves as a stabilizing/reducing agent, followed by hydrothermal treatment at 180 °C. The resulting powder samples were characterized by X-ray diffraction (XRD) phase analysis, infrared spectroscopy (IRS), scanning electron microscopy (SEM), and electron paramagnetic resonance (EPR). The specific surface area and pore size distribution were measured by the Brunauer–Emmett–Taylor (BET) method. Electronic paramagnetic resonance spectra were recorded at room temperature and at 123 K by a JEOL JES-FA 100 EPR spectrometer. The intensity of the bands within the range of 400–1700 cm⁻¹ for biosynthesized ZnO (BS-Zn) powders decreased with the increase in the Mentha arvensis extract concentration. Upon increasing the plant extract concentration, the relative proportion of mesopores in the BS-Zn samples also increased. It was established that the photocatalytic performance of the biosynthesized powders was dependent on the MA concentration in the precursor solution. According to EPR and PL analyses, it was proved that there was a presence of singly ionized oxygen vacancies (V₀⁺) and zinc interstitials (Zn_i). The use of the plant extract led to changes in the morphology, phase composition, and structure of the ZnO particles, which were responsible for the increased photocatalytic rate of discoloration of Malachite Green dye.

Composites based on Mg₂Ni with 5% activated carbon from apricot stones (ACAP) have been prepared by ball milling and subsequent annealing in hydrogen atmosphere. The purpose of the primary metal (Mg, Ni, and V) milling was to reduce the particle size and achieve a good contact between them, without forming intermetallic compounds. During hydriding/dehydriding at 300 °C the amount of the Mg₂Ni phase progressively increased, and after 10 cycles about 50% Mg₂(Ni,V) was achieved. The hydrogenation produced mainly Mg₂NiH₄, but small amounts of MgH₂ and VH_x were also detected in the powder mixture. Relatively high hydrogen storage capacity and fast hydriding/dehydriding kinetics of the Mg_2.1Ni_0.7V_0.3—5 wt.% ACAP composite were determined both from hydrogen gas phase and electrochemically.

Layered sodium transition metal oxides belong to electrode materials for sodium-ion batteries that combine, in a better way, high performance with environmental requirements. However, their cycling stability is still far from desirable. Herein, we demonstrate a rational approach to control the cycling stability of sodium-deficient nickel manganese oxides, Na_2/3Ni_1/2Mn_1/2O₂, with two- and three-layer stacking through Al substitution and Al₂O₃ treatment. Layered Na_2/3Ni_1/2Mn_1/2O₂ oxide displays a limited ability to accommodate aluminum in its structure (i.e., up to 8 at. %). The substitution of Ni ions with electrochemically inactive Al³⁺ ions and keeping the amount of Mn ions in Na_2/3Ni_1/2−xAl_xMn_1/2O₂ leads to the stabilization of the two-layer stacking and favors the participation of lattice oxygen in the electrochemical reaction in addition to Ni ions. This results in an increase in the specific capacity of the Al-substituted oxides. Furthermore, the kinetics of the cationic migration between layers occurring during oxide cycling was manipulated by oxide morphology. The best cycling stability is observed for Na_2/3Ni_0.42Al_0.08Mn_1/2O₂ having a column-like morphology of stacked plate-like particles along the common faces. The treatment of the layered oxides with Al₂O₃ mitigates the Mn dissolution reaction during electrode cycling in the NaPF₆-based electrolyte, thus contributing to a high cycling stability.

In this paper, the crystallization behavior of 50ZnO:47B₂O₃:3Nb₂O₃:0.5Eu₂O₃ (G-0 h) glass has been investigated in detail by DSC, XRD and TEM analysis. The luminescent properties of the resulting glass-ceramics were also investigated. By XRD and TEM analysis, crystallization of several crystalline phases has been proved (α-Zn₃B₂O₆, β-Zn₃B₂O₆ and ZnNb₂O₆). By calculating crystal parameters, it was found that europium ions are successfully incorporated in the β-Zn₃B₂O₆. Photo-luminescent spectra showed increased emission in the resulting glass-ceramic samples compared to the parent glass sample due to higher asymmetry of Eu³⁺ ions in the obtained crystalline phases. It was established that the optimum emission intensity is registered for glass-ceramic samples obtained after 25 h heat treatment of the parent glass.

New results on the effect of TiO₂ on Pd/La₂O₃-CeO₂-Al₂O₃ systems for catalytic oxidation of methane in the presence of H₂O and SO₂ have been received. Low-temperature N₂-adsorption, XRD, SEM, HRTEM, XPS, EPR and FTIR techniques were used to characterize the catalyst. The presence of Ce³⁺ on the catalytic surface and in the volume near the lantana was revealed by EPR and XPS. After aging, the following changes are observed: (i) agglomeration of the Pd-clusters (from 8 nm to 12 nm); (ii) transformation of part of the TiO₂ from anatase to larger particles of rutile; and (iii)—the increase in PdO/Pd—ratio above its optimum. The modification by Ti of the La₂O₃-CeO₂-Al₂O₃ system leads to higher resistance towards the presence of SO₂ most likely due to the prevailing formation of unstable surface sulfites instead of thermally stable sulfates. Based on kinetic model calculations, the reaction pathway over the Pd/La₂O₃-CeO₂-TiO₂-Al₂O₃ catalyst follows the Mars–van Krevelen mechanism. For evaluation of the possible practical application of the obtained material, a sample of Pd/La₂O₃-CeO₂-TiO₂-Al₂O₃, supported on rolled aluminum-containing stainless steel (Aluchrom VDM^®), was prepared and tested. Methane oxidation in an industrial-scale monolithic reactor was simulated using a two-dimensional heterogeneous reactor model.

We present the development of alternative scaffolds and validation of their synthetic pathways as a tool for the exploration of new HIV gp120 inhibitors based on the recently discovered inhibitor of this class, NBD-14136. The new synthetic routes were based on isosteric replacements of the amine and acid precursors required for the synthesis of NBD-14136, guided by molecular modeling and chemical feasibility analysis. To ensure that these synthetic tools and new scaffolds had the potential for further exploration, we eventually tested few representative compounds from each newly designed scaffold against the gp120 inhibition assay and cell viability assays.