We investigate the sound response of graphene membranes via laser Doppler vibrometry. We show that graphene's mechanical compliance is superior to that of MEMS devices and thus can enable the fabrication of smaller and more performant microphones.

TiO₂ and CeO₂ are well known as oxygen sensing materials. Despite high sensitivity, the actual utilization of these materials in gas detection remains limited. Research conducted over the last two decades has revealed synergistic effects of TiO₂-CeO₂ mixed oxides that have the potential to improve some aspects of oxygen monitoring. However, there are no studies on the sensing properties of the TiO₂-CeO₂ obtained by mechanochemical treatment. We have tested the applicability of the mechanochemically treated TiO₂-CeO₂ for oxygen detection and presented the results in this study. The sensing layers are prepared as a porous structure by screen printing a thick film on a commercial substrate. The obtained structures were exposed to various O₂ concentrations. The results of electrical measurements showed that TiO₂-CeO₂ films have a significantly lower resistance than pure oxide films. Mixtures of composition TiO₂:CeO₂ = 0.8:0.2, ground for 100 min, have the lowest electrical resistance among the tested materials. Mixtures of composition TiO₂:CeO₂ = 0.5:0.5 and ground for 100 min proved to be the most sensitive. The operating temperature can be as low as 320 °C, which places this sensor in the class of semiconductor sensors working at relatively lower temperatures.

Diatom samples were collected during July 2010 at 15 localities from different types of substrate (stone surfaces, sand, mud, filamentous algae and submerged mosses) from the Dojkinci River. During the research period, 124 taxa were determined within 43 genera. Among numerous common diatoms we recorded three taxa for the first time in Serbia: Brachysira intermedia (Øst.) Lange-Bertalot, Chamaepinnularia mediocris (Krass.) Lange-Bertalot and Navicula tridentula Krass. Also, we observed 21 taxa which are rarely recorded taxa for Serbia. The most interesting was Diatomella balfouriana Grevill. that was previously known only from the River Tisa near Titel. In the studied material, it was identified only in samples collected from the surface of boulders with mosses at the third locality. Their morphology, distribution and ecology are presented in this paper.

In this study, we conducted a comprehensive investigation of newly synthesized fullerene derivatives developed for potential application in perovskite solar cells (PSCs). We explored three novel dihydrofuran-fused C₆₀ fullerene derivatives (13, 14, and 15) that were specifically designed to enhance solubility and interaction with the substrate, fluorine-doped tin oxide (FTO). A comparative analysis was performed, with reference to the widely used phenyl-C61-butyric acid methyl ester (PCBM) and compound 12, from which 13, 14, and 15 are derived, to assess the impact of sugar units on materials properties. The synthesized compounds demonstrated significant solubility in common organic solvents, a critical factor in their potential application in wet-processed PSCs. Our investigation included electrochemical property analysis, thin film deposition, surface characterization, and electrochemical impedance spectroscopy (EIS). EIS measurements unveiled key insights into charge transfer properties at the electrode/electrolyte interface, making the compounds attractive candidates for electron transport layers (ETLs) in PSCs.

The key equipment for performing aerodynamic testing of objects, such as road and railway vehicles, aircraft, and wind turbines, as well as stationary objects such as bridges and buildings, are multichannel pressure measurement instruments (pressure scanners). These instruments are typically based on arrays of separate pressure sensors built in an enclosure that also contains temperature sensors used for temperature compensation. However, there are significant limitations to such a construction, especially when increasing requirements in terms of miniaturization, the number of pressure channels, and high measurement performance must be met at the same time. In this paper, we present the development and realization of an innovative MEMS multisensor chip, which is designed with the intention of overcoming these limitations. The chip has four MEMS piezoresistive pressure-sensing elements and two resistive temperature-sensing elements, which are all monolithically integrated, enabling better sensor matching and thermal coupling while providing a high number of pressure channels per unit area. The main steps of chip development are preliminary chip design, numerical simulations of the chip’s mechanical behavior when exposed to the measured pressure, final chip design, fabrication processes (photolithography, thermal oxidation, diffusion, layer deposition, micromachining, anodic bonding, and wafer dicing), and electrical testing.