Ana Sofia Castro

Ana Sofia Castro

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 June 2024 in Polymers
Verified
Journal Article
Open access
PDF file
ACAna Sofia Castro
Ana Sofia Castro
BCBárbara D. D. Cruz
Bárbara D. D. Cruz
Daniela M. CorreiaDaniela M. Correia
Daniela M. Correia
Senentxu Lanceros-MendezSenentxu Lanceros-Mendez
Senentxu Lanceros-Mendez
Pedro MartinsPedro Martins
Pedro Martins
The pollution of aquatic environments is a growing problem linked to population growth and intense anthropogenic activities. Because of their potential impact on human health and the environment, special attention is paid to contaminants of emerging concern, namely heavy metals. Thus, this work proposes the use of naturally derived materials capable of adsorbing chromium (VI) (Cr(VI)), a contaminant known for its potential toxicity and carcinogenic effects, providing a sustainable alternative for water remediation. For this purpose, membranes based on chitosan (CS) and chitosan/Kraft lignin (CS/KL) with different percentages of lignin (0.01 and 0.05 g) were developed using the solvent casting technique. The introduction of lignin imparts mechanical strength and reduces swelling in pristine chitosan. The CS and CS/0.01 KL membranes performed excellently, removing Cr(VI) at an initial 5 mg/L concentration. After 5 h of contact time, they showed about 100% removal. The adsorption process was analyzed using the pseudo-first-order model, and the interaction between the polymer matrix and the contaminant was attributed to electrostatic interactions. Therefore, CS and CS/KL membranes could be low-cost and efficient adsorbents for heavy metals in wastewater treatment applications.

1 April 2026 in Advanced Materials
Verified
Journal Article
Open access
PDF file
ASAndrey Shibaev
Andrey Shibaev
Jon MaizJon Maiz
Jon Maiz
VPViktor Petrenko
Viktor Petrenko
AIAmaia Iturrospe
Amaia Iturrospe
JMJosu Fernández Maestu
Josu Fernández Maestu
Senentxu Lanceros-MendezSenentxu Lanceros-Mendez
Senentxu Lanceros-Mendez
A multiscale understanding of the structure of ionogels – nanoparticle‐free polymer composites incorporating ionic liquids – is essential for enhancing their macroscopic functional properties and unlocking their potential in critical applications such as energy storage, sensing, and actuation. We establish a complete picture of the nano‐ and microstructuration of an ionic liquid within the matrix of a practically relevant electroactive copolymer poly(vinylidenefluoride‐ co ‐trifluoroethylene), by combining neutron scattering with cryogenic scanning electron tomography assisted by focused ion beam milling and cryogenic transmission electron microscopy with elemental analysis. We show that the ionic liquid is primarily located in the polymer amorphous phase and forms nanostructures with 10–12 nm size. It does not penetrate into the crystalline lamellae or the polymer amorphous phase confined between them, and it does not affect the polymer degree of crystallinity nor its complete crystallization in the highly electroactive β‐phase. Saturation of the unconfined amorphous phase with ionic liquid is identified as the key factor enabling high ionic conductivity while preserving mechanical integrity. At high ionic liquid concentrations, its excess microphase‐separates during the composite processing and accumulates in predominantly interconnected micrometer‐sized pores, providing the magnetoelectric response and further increasing the ionic conductivity.

16 November 2025 in Advanced Materials Technologies
Verified
Journal Article
Open access
NPNelson Pereira
Nelson Pereira
ACAna Sofia Castro
Ana Sofia Castro
Cristian Mendes-FelipeCristian Mendes-Felipe
Cristian Mendes-Felipe
Daniela M. CorreiaDaniela M. Correia
Daniela M. Correia
Senentxu Lanceros-MendezSenentxu Lanceros-Mendez
Senentxu Lanceros-Mendez
Iontronic materials show high performance for applications as pressure sensors due to the formation of the electric double layers (EDLs) at the dielectric/electrode interface. The properties of iontronic materials can be tuned, allowing the sensor to be customized for varied pressure ranges and ambient conditions. Furthermore, additive printing techniques enable to obtain customized cost‐effective complex sensor designs, opening up new applications in the fields of medical devices, automotive systems, and consumer electronics. This work demonstrates the manufacturing process of a pressure sensor by stereolithography (SLA) 3D printing of a Liqcreate Flexible X resin in a gyroid framework, accounting for structural density variations. Furthermore, different concentrations (5 and 20% wt.) of the ionic liquid (IL) 1‐butyl‐3‐methyl imidazolium thiocyanate ([Bmim][SCN]) are used to tune the EDL and maximize the sensor sensitivity. The capacitance response to applied pressure is analyzed across different designs. The configuration with 20% wt. IL content and lower quantity of pores exhibited superior performance, achieving a pressure sensitivity of 0.065 kPa −1 throughout a pressure range of 60 kPa. This study demonstrated the simple manufacturing process and ability to improve commercially available resins with ionic liquid, to achieve highly customized sensors.