Jimin Lee

Ms. Jimin Lee


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 June 2024 in Polymers
Verified
Journal Article
Open access
PDF file
MKMijoo Kim
Mijoo Kim
JLJimin Lee
Jimin Lee
Chan  Park Chan Park
Chan Park
DJDeuk-Won Jo
Deuk-Won Jo
BYBo Yu
Bo Yu
RKReuben Kim
Reuben Kim
The development of high-filled 3D printing resin necessitates a bonding protocol for dental indirect restorations to achieve optimal bond strength after cementation. This study evaluates shear bond strengths of high-filler 3D printed materials for permanent restorations with various surface treatments. Rodin Sculpture 1.0 (50% lithium disilicate fillers) and 2.0 Ceramic Nanohybrid (>60% zirconia and lithium disilicate fillers) were tested, with Aelite All-Purpose Body composite resin as control. Samples were prepared, post-cured, and sandblasted with alumina (25 µm). Surface roughness was analyzed using an optical profilometer. Two bonding protocols were compared. First, groups were treated with lithium disilicate silane (Porcelain Primer) or zirconia primer (Z-Prime Plus) or left untreated without a bonding agent. Beam-shaped resin cement (DuoLink Universal) specimens were bonded and stored in a 37 °C water bath. Second, additional sets of materials were coated with a bonding agent (All-Bond Universal), either followed by silane application or left untreated. These sets were then similarly stored alongside resin cement specimens. Shear bond tests were performed after 24 h. SEM images were taken after debonding. One-Way ANOVA and post hoc Duncan were performed for the statistical analysis. Rodin 1.0 exhibited increased adhesive failure with silane or zirconia primer coating, but significantly improved bond strengths with bonding agent application. Rodin 2.0 showed consistent bond strengths regardless of bonding agent application, but cohesive failure rates increased with bonding agent and filler coating. In all groups, except for Rodin 1.0 without bonding agent, silane coating increased cohesive failure rate. In conclusion, optimal shear bond strength for high-filler 3D printing materials can be achieved with silane coating and bonding agent application.

8 February 2025 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
MPMitsu Patel
Mitsu Patel
JLJimin Lee
Jimin Lee
MHMarc Hayashi
Marc Hayashi
RKReuben Kim
Reuben Kim
MKMijoo Kim
Mijoo Kim
This study investigated the susceptibility of nine composite resins to turmeric staining, evaluated bleaching efficacy for color recovery, and assessed surface hardness throughout these processes. Disc-shaped specimens (8 mm × 2 mm, n = 3/group) were subjected to daily 20 min turmeric solution immersion for two weeks, followed by two weeks of daily 3 h applications of 16% carbamide peroxide bleaching. Color measurements included spectrophotometric analysis for ΔE values (threshold ΔE > 3.3 for clinical significance) and VITA Classic shade assessment at baseline, post-staining, and post-bleaching intervals. Surface hardness was evaluated using a Vickers hardness tester. Results showed significant color changes in all materials except HA after turmeric exposure, with FS exhibiting the highest staining susceptibility (ΔE = 24.6 ± 2.69) and HA showing minimal change (ΔE = 1.9 ± 0.85). VITA Classic shade evaluation revealed varying patterns; some materials maintained their initial shade designation despite significant ΔE changes (FS, CM), while others showed substantial shade shifts with successful recovery post-bleaching (HA, OM). Bleaching effectiveness varied across materials, with PO, VEP, and FS demonstrating substantial recovery in ΔE values, although FS retained clinically noticeable discoloration post-bleaching (ΔE = 7.6 ± 0.89). Surface hardness analysis revealed three distinct groups: high (80–90 HV: FS, CA, VPO), intermediate (55–70 HV: VEP, OM), and low (40–47 HV: PO, AE, HA, CM). For patients with high exposure to chromogenic foods, such as turmeric, material selection requires careful consideration of staining susceptibility, with HA and OM demonstrating superior color stability and recovery characteristics in this study.