ILIAS GEORGIOPOULOS

Mr. ILIAS GEORGIOPOULOS


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 January 2024 in Nanomaterials
Verified
Journal Article
Open access
PDF file
ABAmaia Soto Beobide
Amaia Soto Beobide
RBRudolf Bieri
Rudolf Bieri
ZSZoltán Szakács
Zoltán Szakács
KSKevin Bela Sparwasser
Kevin Bela Sparwasser
IKIoanna G. Kaitsa
Ioanna G. Kaitsa
George VoyiatzisGeorge Voyiatzis
George Voyiatzis
Nanomaterials are integrated within consumer products to enhance specific properties of interest. Their release throughout the lifecycle of nano-enabled products raises concerns; specifically, mechanical strains can lead to the generation of fragmented materials containing nanomaterials. We investigated the potential release of single-walled carbon nanotubes (SWCNTs—brand TUBALL™) from epoxy composite materials. A pin-on-disk-type tribometer was used for the accelerated mechanical aging of the nanocomposites. A pristine nanocomposite material, abraded material and debris obtained from the abrasion in the tribometer were analyzed by Raman spectroscopy. The airborne-produced particles were captured using particle collectors. Stat Peel’s Identifier C2 system was used to monitor the SWCNT content of respirable particles produced during the abrasion test. The SWCNT amounts found were below the LoQ. The Raman spectra conducted on the Stat Peel filters helped identify the presence of free SWCNTs released from the epoxy matrix, although they were notably scarce. Raman spectroscopy has been proved to be a crucial technique for the identification, characterization and assessment of structural changes and degradation in SWCNTs that occurred during the abrasion experiments.

24 September 2025 in Nanomanufacturing
Verified
Journal Article
Open access
PDF file
IGILIAS GEORGIOPOULOS
ILIAS GEORGIOPOULOS
DGDimitra Giasafaki
Dimitra Giasafaki
CAConstantina Dia Andreouli
Constantina Dia Andreouli
CSCharikleia Ioakeim Sarafoglou
Charikleia Ioakeim Sarafoglou
Atmospheric plasma spraying was used to create composite coatings employing mixed alloy matrices supplemented with carbon-based solid lubricants as feedstock materials. The current study’s goal was to examine the tribological properties of these coatings and explore the potential benefits of using CNTs as a nano-additive to minimize wear and friction while enhancing lubrication conditions in tribosystems such as piston ring–cylinder liner systems. Pin-on-disk measurements are used to correlate the chemical composition of feedstock materials with the friction coefficient and wear rate during coating operation. The enhanced behavior of the produced coatings is investigated. The anti-wear performance of Co-based cermet and metal alloys coatings, as well as the enhanced lubrication conditions during operation, are shown. In-depth discussion is provided regarding how the features of the feedstock powder affect the quality and performance of the produced coatings. The results showed that coatings based on the CoMo alloy exhibited an increase in wear due to CNT agglomeration. In contrast, CNT addition led to an improvement in bonding strength by up to 33%, a reduction in wear rate by up to 80%, and a decrease in the coefficient of friction from approximately 0.70 to 0.35 in CoNi cermet coatings. These findings demonstrate the role of CNTs in coating performance for demanding tribological applications.

7 November 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
Nikolaos GalanisNikolaos Galanis
Nikolaos Galanis
EREleni Roussi
Eleni Roussi
IKIoanna Kitsou
Ioanna Kitsou
IGILIAS GEORGIOPOULOS
ILIAS GEORGIOPOULOS
Dimitrios  Manolakos Dimitrios Manolakos
Dimitrios Manolakos
CAConstantina-Dia Andreouli
Constantina-Dia Andreouli
Hip joint surgeries, including total hip replacement or resurfacing, have increased tremendously in the last decades. Number of patients of all ages, replace their hip, due to severe injuries or trauma problems, so as to have a better life. According to these factors, new material and processes in implants manufacturing are imported to medicine, through research programs, every year. In the scope of one of these programs, that has to do with ceramic coatings on metallic resurfacing implants, a new 3axis Hip simulator was designed and manufactured in the Laboratory of Manufacturing Technology of the National Technical University of Athens. The scope of this paper is to present the main parts, materials and process used to manufacture the simulator as well as the way the simulator is working and how its movement in 3axis is accomplished. Furthermore, the evaluation of the machine and its use to examine resurfacing implants is presented.