The structure of the new ternary eutectic Al-Ca-Cu system considered as a replacement for the ternary eutectic system Al-Ce-Cu widely used for additive manufacturing has been studied using experimental techniques. The liquidus projection of the Al-Ca-Cu system in the aluminum corner has been suggested based on experiential studies of the microstructure and phase composition of model alloys. The suggested structure of the diagram has two quasi-binary sections: (Al)-Al₂₇Ca₃Cu₇ and (Al)-Al₈CaCu₄ and three invariant eutectic transformations: L→(Al) + (Al,Cu)₄Ca + Al₂₇Ca₃Cu₇ (at 5.6 wt.% Ca, 4.5 wt.% Cu, 595 °C), L→(Al) + Al₂₇Ca₃Cu₇ + Al₈CaCu₄ (at 2.2 wt.% Ca, 13.5 wt.% Cu, 594 °C) and L→(Al) + Al₈CaCu₄ + Al₂Cu (at 0.5 wt.% Ca, 34 wt.% Cu, 544 °C). The limit solubility of copper in aluminum solid solution (Al) at 530 °C reaches ~5.1 wt.% in the ternary phase field (Al) + Al₈CaCu₄ + Al₂Cu and drops to ~2.4 wt.% in the (Al) + Al₈CaCu₄ + Al₂₇Ca₃Cu₇ ternary phase field. For the example of the model ternary hypoeutectic alloys with a predominant content of the eutectic (Al,Cu)₄Ca phase, it has been shown that the system is promising for designing new eutectic-type alloys with a natural composite structure.

In this study, ceramic coatings were grown on the surface of as-cast aluminum alloys via plasma electrolytic oxidation (PEO). The effect of the Si- and Ca-alloying elements in aluminum on the growth process, morphology, composition, mechanical, and corrosion properties of the PEO coatings was investigated. Uniform coatings with a minimum number of defects were formed on the surfaces of Al–Ca alloys. Increasing the Si content in Al led to an increase in the bulk and surface porosity of the coatings. The α-Al₂O₃ phase mainly formed in the coatings synthesized on pure Al and Al–Ca alloys, while an increased amount of Si in Al alloys hindered the formation of the α-Al₂O₃ phase. The coatings had a microhardness of 660–1180 HV_, which was 20–30 times higher than that of the original as-cast alloy. Moreover, the coating on the Al–Ca alloys had the highest peak hardness, which was probably caused by the formation of a greater amount of the α-Al₂O₃ phase. Electrochemical studies in 3.5% NaCl have shown that PEO coatings reduce the corrosion current density. Of all PEO-treated alloys, Al and Al1Ca have the lowest corrosion current density and hence the highest corrosion resistance due to the composition and uniformity of the coating.

Aluminum alloys are one of the most common structural materials. To improve the mechanical properties, an alloy of the Al–Zn–Mg–Ca–Fe system was proposed. In this alloy, when Fe and Ca are added, compact particles of the Al₁₀CaFe₂ compound are formed, which significantly reduces the negative effect of Fe on the mechanical properties. Because of the high solidification rate (about 600 K/s) during cylindrical ingot (~33 mm) production, the electromagnetic casting method (ECM) makes it possible to obtain a highly dispersed structure in the cast state. The size of the dendritic cell is ~7 μm, while the entire amount of Fe is bound into eutectic inclusions of the Al₁₀CaFe₂ phase with an average size of less than 3 μm. In this study, the effect of radial shear rolling (RSR) on the formation of the structure and hardening of the Al–8%Zn–3.3%Mg–0.8%Ca–1.1%Fe alloy obtained by EMC was studied. Computer simulation of the RSR process made it possible to analyze the temperature and stress–strain state of the alloy and to select the optimal rolling modes. It was shown that the flow features during RSR and the severe shear strains near the surface of the rod (10 mm) provided a refining and decrease in the size of the initial Fe-containing particles.

The effects of Fe-bearing phases on the structure, mechanical properties, and fracture mechanism of a non-heat-treatable model sheet alloy (wt.%: Al–2%Cu–1.5%Mn(-Mg,Zn)), designed for Al₂₀Cu₂Mn₃ dispersoids, was investigated. This involved a combination of thermodynamic modeling in the Thermo-Calc program and experimental studies of structure and mechanical properties. It has been shown that the addition of 0.5 and 0.4% iron and silicon leads to the formation of eutectic inclusions in the Al₁₅(Mn,Fe)₃Si₂ phase. In addition to the Fe- bearing inclusions, the formation of the eutectic Al₂Cu and Al₂CuMg phases can be expected in the as-cast structure of the experimental alloys. Despite their relatively high fraction of eutectic particles, non-homogenized alloy ingots demonstrated sufficiently high deformation processability during the hot (400 °C) and cold rolling, which made it possible to obtain high-quality sheet alloys (with reduction degrees of 80 and 75%, respectively). The results of the tensile tests revealed that, after cold rolling, the addition of 1% Mg significantly increased the tensile and yield strengths, whereas the effect of 1% Zn was negligible. At the same time, the uniform distribution of Fe-bearing phases in the structure of the cold-rolled sheets contributes to the preservation of the dimple mechanism of the fracture toughness. This helps to maintain the same level of ductility for the cold-rolled sheet Fe-containing alloys as for Fe-free alloys. It has been shown, based on the data obtained, that adding Fe, Si, Mg, and Zn to the base Al–2%Cu–1.5%Mn alloy in a total amount of more than 3% makes it possible to retain the ductile fracture patterns of the base alloy and obtain a fairly higher level of mechanical properties. This suggests the fundamental possibility of using a variety of secondary raw materials (containing the main elements present in aluminum alloys of different alloying systems) to prepare a base alloy that does not require homogenization or thermal hardening.

This study is focused on the design of new Al–Cu–Mn alloys with enhanced strength and heat resistance achieved without high-temperature exposur