Machines with highly saturated magnetic circuits are utilized to maximize drive efficiency. However, their control is non-trivial due to highly non-linear characteristics, and therefore, an accurate parameter identification procedure is crucial. This paper presents and validates a comprehensive flux linkage identification procedure. Several steps needed for accurate parameter identification and their influence on the estimation results are described. The impact of all main parts of the electrical drive, i.e., dead times introduced between switching off and switching on the power transistors, phase delay from the current low-pass filters, delay from the control system, and misalignment of the axis angle due to the machine asymmetries is considered and partially eliminated. An improved identification procedure with the look-up table-based dead time compensation and estimation of equivalent circuit resistance is applied to estimate the parameters of the highly saturated PMSM traction machine from the fourth generation of the Toyota Prius, and the obtained results are compared with a Finite Element Method-based model of this machine. Finally, dynamic test results are conducted to prove the proposed approach’s accuracy.
The automotive market is very competitive and demands consistently improving the technologies used and reducing the product cost and dimensions with each product model iteration. Hence, it is important to have access to well-defined reference designs of high-quality products to evaluate new ideas and technologies. This paper provides readers with a numerical model of such a high-quality product, i.e., the IPMSM-type traction motor from the fourth generation of the Toyota Prius hybrid transaxle. The presented results also serve for a discussion regarding the design decisions of the Toyota engineers and the applicability of the linearized machine model for the approximated torque calculations. In the introductory section, a brief history of the Prius model and references to the reverse engineering reports are given. Afterward, the machine dimensions, material properties, and winding configuration are described. Then, the model is validated with the torque measurements at constant speed. The simulation results are presented in the next chapters, and the numerical source data are supplied to the reader. Finally, the design philosophy of the Toyota drive is briefly discussed in comparison with the BMWi3 drive and the results are concluded in the last section.
The paper presents the results of a 3D FEA simulations series of a dual air gap Axial Flux (AF) electric machine with Surface-Mounted Permanent magnets (SPM) with parameterized rotor geometry. Pole number and pole span influence on back-emf, as well as cogging and ideal electromagnetic torques angular characteristics were investigated for each model with the common segmented yokeless stator with concentric windings. Synchronous and BLDC drives supply were used to estimate back-emf distortion. Ideal torque ripple and cogging torque spectra were analyzed. It was concluded that the number of poles closer to the number of slots with ~0.8 pole span tends to yield good torque density with the lowest cogging torque, back-emf distortion and ideal torque ripple.
21 April 2025 in IEEE Transactions on Industrial Electronics
Torque control performance is essential in propulsion control systems, especially in automotive applications. Together with torque maximization, it becomes a desirable feature to ensure efficient operation of the drive system. At high power density, the phenomenon of self and cross-saturation occurs in the controlled machine, revealing torque and performance deterioration if not considered. Hence, this article proposes a novel approach for torque control of an interior permanent magnet synchronous motor (IPMSM) based on an augmented state-feedback controller (ASFC) with flux-linkage control. The proposed approach, in contrast to classical PI-based current control systems, allows for simplification of the plant’s mathematical description. As a result, a stationary, linear controller may be designed. The mathematical model of the assumed machine (Toyota Prius 4rd generation) is provided with a torque maximization approach. The ASFC structure and synthesis procedure are discussed in detail. The experimental results indicate excellent torque tracking performance and wide torque control bandwidth of the proposed ASFC.
The automotive market is very competitive and presents a demand for the consistent improvement of the used technologies and reduction of the product cost and dimensions with each product model iteration. Hence, it is important to have access to well-defined reference designs of high quality products, in order to evaluate the new ideas and technologies. This paper provides the readers with a numerical model of such a high quality product, i.e., the IPMSM type traction motor from the 4th generation of the Toyota Prius hybrid transaxle. In the introductory section, the brief history of the Prius model is given together with the references to the reverse engineering reports. Afterwards, the machine dimensions, material properties and winding configuration are described. Then, the model is validated with the torque measurements at constant speed. In the next chapters the simulation results are presented and the numerical source data are supplied to the reader. Finally, the design philosophy of the Toyota drive is briefly discussed in comparison with the BMWi3 drive and the results are concluded in the last section.