Michal Gierczynski

Dr. Michal Gierczynski

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 December 2024 in Energies
Verified
Journal Article
Open access
PDF file
MGMichal Gierczynski
Michal Gierczynski
RJRafał Jakubowski
Rafał Jakubowski
EKEmil Kupiec
Emil Kupiec
LNLukasz J. Niewiara
Lukasz J. Niewiara
Tomasz TarczewskiTomasz Tarczewski
Tomasz Tarczewski
LGLech M Grzesiak
Lech M Grzesiak
Machines with highly saturated magnetic circuits are utilized to maximize drive efficiency. However, their control is non-trivial due to highly non-linear characteristics, and therefore, an accurate parameter identification procedure is crucial. This paper presents and validates a comprehensive flux linkage identification procedure. Several steps needed for accurate parameter identification and their influence on the estimation results are described. The impact of all main parts of the electrical drive, i.e., dead times introduced between switching off and switching on the power transistors, phase delay from the current low-pass filters, delay from the control system, and misalignment of the d–axis angle due to the machine asymmetries is considered and partially eliminated. An improved identification procedure with the look-up table-based dead time compensation and estimation of equivalent circuit resistance is applied to estimate the parameters of the highly saturated PMSM traction machine from the fourth generation of the Toyota Prius, and the obtained results are compared with a Finite Element Method-based model of this machine. Finally, dynamic test results are conducted to prove the proposed approach’s accuracy.

21 April 2021 in Energies
Verified
Journal Article
Open access
PDF file
MGMichal Gierczynski
Michal Gierczynski
LGLech M Grzesiak
Lech M Grzesiak
This paper presents a finite element method (FEM)-based model, which describes the magnetic circuit of the BMW i3 traction machine. The model has been reconstructed based on data available in the public domain. The reader is provided with numerical data regarding flux linkage surfaces in d- and q-axes, as well as with all the information needed to develop a space-vector model of the machine in steady-state, taking into consideration the non-linearity of the magnetic circuit. Hence, the data of a highly-saturated machine from a renowned product are provided, which can serve as a reference design for research. After that, torque curve and partial load operation points are calculated. Finally, the machine model is linearized and the calculations are repeated with the simplified linearized model. The results from both models are then compared with each other. This comparison is intended to assess the magnitude of the expected inaccuracies, when simplified analytical tools are applied to highly-saturated machines (which are the backbone of automotive electrical drivetrains). It is especially important with regard to preliminary design of electrical drivetrains, as at this stage detailed machine geometry and materials are not known.

14 July 2021 in Energies
Verified
Journal Article
Open access
PDF file
MGMichal Gierczynski
Michal Gierczynski
LGLech M Grzesiak
Lech M Grzesiak
AKArkadiusz Kaszewski
Arkadiusz Kaszewski
This paper deals with a well-known problem of the transient DC-bias current occurring during a phase shift transition in dual active bridge (DAB) DC/DC converters. This phenomenon, if not compensated, can cause damage to the converter or deteriorate its performance. One aim of this paper is to present a solution which allows for the elimination of the undesired transient DC-bias component in current waveforms. This solution is the dual rising edge shift (DRES) compensation algorithm. It provides a very simple implementation and fast settling time within the first half of a switching period. Moreover, the solution is independent on any measurements or system parameter values. It is based on the double-sided single phase shift (DSSPS) modulation, which is described in detail along with a converter model in steady-state. Then, the mechanisms leading to the transient DC-bias are explained, and the compensation algorithm is derived. The performance of the algorithm has been tested using a laboratory prototype. A comprehensive set of tests, involving rapid step changes in power flow and frequency sweep, are provided. Finally, the features of the proposed algorithm are briefly discussed.

29 September 2021 in Energies
Verified
Journal Article
Open access
PDF file
MGMichal Gierczynski
Michal Gierczynski
LGLech M Grzesiak
Lech M Grzesiak
AKArkadiusz Kaszewski
Arkadiusz Kaszewski
The paper describes the cascaded voltage and current control for a bidirectional DC/DC converter in Dual Active Bridge (DAB) topology. The typical DAB converter circuit was extended by additional current filters, which allow it to operate in application fields with high requirements on current ripples. The core concept of the presented solution is usage of the modified Single Phase Shift (SPS) modulation, which allows to compensate for the DC-bias current occurring in dynamic states and provides a settling time of half switching cycle during transients. Its features were utilized to build a simplified dynamic model of the converter. The linear Proportional-Integral (PI) controllers are used in both voltage and current control loops. Based on the developed dynamic models, the tuning rules for both controllers were derived. In both cases, a number of the tuned parameters were reduced from two to one (which can present a great practical value for application engineers). The proposed solutions are validated based on a laboratory prototype. An important part of the experiments was devoted to non-linear effects occurring near the current limitation boundary of the system. The paper ends with a brief discussion regarding the future research directions.

10 October 2023 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
LNLukasz J. Niewiara
Lukasz J. Niewiara
Tomasz TarczewskiTomasz Tarczewski
Tomasz Tarczewski
MGMichal Gierczynski
Michal Gierczynski
LGLech M Grzesiak
Lech M Grzesiak
Drives with a reluctance synchronous motor (RSM) are currently being intensively developed due to the simple construction and easily available materials used for their construction. These machines are also characterized by high efficiency. Designing a control system is not trivial due to the nonlinearity of the model describing this motor. In order to simplify the mathematical model of RSM, a linearization technique based on the lumped perturbation approach was proposed. A modified mathematical description of flux surface and inductance was proposed and applied. An original hybrid state feedback control (SFC) structure of a drive with a reluctance synchronous motor has been proposed. In the range of admissible changes of state variables, the regulator operates in the linear region and has the structure of an SFC. When the state variable limits (maximum values) are reached, the control structure performs predictive control to maintain the limit values. The synthesis of the control structure is described in detail. The proposed control structure is experimentally compared with a cascade control and model predictive one. The obtained results indicate a similar dynamical behavior and much better load torque compensation obtained for hybrid SFC. The proposed approach assures precise limitation of state variables resulting safe operation of the drive.

25 September 2024 in Energies
Verified
Journal Article
Open access
PDF file
MGMichal Gierczynski
Michal Gierczynski
RJRafał Jakubowski
Rafał Jakubowski
EKEmil Kupiec
Emil Kupiec
MSMirosław Seredyński
Mirosław Seredyński
MJMaciej Jaworski
Maciej Jaworski
LGLech M Grzesiak
Lech M Grzesiak
The automotive market is very competitive and demands consistently improving the technologies used and reducing the product cost and dimensions with each product model iteration. Hence, it is important to have access to well-defined reference designs of high-quality products to evaluate new ideas and technologies. This paper provides readers with a numerical model of such a high-quality product, i.e., the IPMSM-type traction motor from the fourth generation of the Toyota Prius hybrid transaxle. The presented results also serve for a discussion regarding the design decisions of the Toyota engineers and the applicability of the linearized machine model for the approximated torque calculations. In the introductory section, a brief history of the Prius model and references to the reverse engineering reports are given. Afterward, the machine dimensions, material properties, and winding configuration are described. Then, the model is validated with the torque measurements at constant speed. The simulation results are presented in the next chapters, and the numerical source data are supplied to the reader. Finally, the design philosophy of the Toyota drive is briefly discussed in comparison with the BMWi3 drive and the results are concluded in the last section.