This research presents a proposal for alkali-activated permeable concrete composites with the use of industrial by-products, including ground granulated blast-furnace slag (GGBS) and waste-foundry sand, as well as agro-desecrate product, i.e., sugarcane bagasse ash (SBA). GGBS and SBA served as binders, with crushed granite as coarse aggregate and waste-foundry sand as fine aggregate. The novelty of this proposal is in examining the influence of SBA, in combination with slag, on the fresh- and hardened-state properties of the proposed permeable concretes. Experiments were conducted to optimize the SBA percentage based on hydraulic conductivity and compressive and tensile strength after 28 days of air curing. The hardened density, compaction factor (workability), and saturated water absorption were also measured for all the mixes. Furthermore, the control and optimal mixes were subjected to evaluate the microstructure analysis (EDX, XRD, and FESEM) after 28 days of air curing. The mix containing 100% GGBS and 0% SBA served as the reference, with the optimal 10% SBA mix (with 90% GGBS) used for comparative analysis to understand its effect on the properties of permeable composites. The results showed positive or acceptable mechanical performance at a mix ratio of 10% SBA to 90% GGBS as binders. This study aims to enhance the understanding of the engineering behavior of alkali-activated permeable composites, facilitating the rational design of permeable pavement systems through the effective use of agro-industrial waste products, thereby conserving ecosystems while meeting engineering requirements.
3D printing is becoming increasingly popular in the construction sector. 3D printing offers the potential to reduce costs, construction time and construction waste. However, due to its high cement content, 3D printable concrete more expensive to produce. The article includes a brief literature survey on the possibility of using cement and aggregate substitutes in concrete mixtures and their impact on fresh composite properties and identifies a research gap. Herein, we propose the use of waste copper slag as a replacement for cement in 3D printable concrete. We examine the effect of replacing cement with copper slag at 5 and 10% on fresh properties of cementitious mortar. The results show that copper slag improves the workability of the mixture and lowers the design yield strength up to 44%, thereby facilitating printing. Even 30% higher fresh compressive strengths were also obtained, which suggest that the buildability of mortars containing copper slag will be improved.
This study examines how cement particle size (modified through sieving) affects the fresh and hardened properties of lightweight mortars, with emphasis on early-age microstructural development and environmental performance. The experimental program included three levels of cement fineness and applied advanced characterization techniques such as X-ray diffraction (XRD), thermogravimetric analysis (TGA), and transmission electron microscopy (TEM) during the first 12 h of hydration. Results demonstrate that finer cement particles enhance workability and increase bulk density due to improved particle packing. While tensile strength slightly decreases, compressive strength increases significantly, especially after 7 days, attributed to accelerated hydration kinetics confirmed by microstructural evidence. A comprehensive life cycle assessment (LCA) shows that finer cement requires more energy to process, but the increased strength-to-emission ratio makes it a cost-effective and sustainable option. Screening cement to below 50 μm enabled up to 14% reduction in CO₂ emissions per unit strength. However, increased shrinkage in finer systems may compromise long-term durability due to greater crack susceptibility. The proposed LCA-based framework supports balancing performance gains with environmental costs in cementitious material design.
Currently, the significance of oil refinery industry is unquestionable because of the increasing demand for petrochemical products, such as fuels, monomers, and organic chemicals. Despite this, apart from high greenhouse gas emissions, numerous oil and natural gas refining processes are distinctly associated with the generation of a considerable amount of Oil Refinery Wastes (ORWs) in different forms, which need proper disposal and valorization. Nonetheless, at present, solid ORWs are mainly sent to landfills. Such a procedure, apart from high disposal costs, results in significant environmental pollution related to the release of chemical contaminants to soil and water environment. Consequently, these pollutants might poison natural flora and digestive systems of animals, thereby contributing to the general degradation of useful land and a serious health risk. To cope with that issue, ORW recycling in cement-based materials might be considered a reliable course of action, as the hardened concrete is capable to bind contaminants that ORW comprises. This article focuses on actual literature knowledge, limitations, and chances in the scope of a comprehensive approach to sustainable management of ORWs through their utilization in cementitious composites. The special emphasis was placed on presenting the impact provided by the addition of ORWs on the numerous performances of cementitious mixes and hardened concrete. The environmental and economic aspects were also discussed, particularly in the scope of CO2 emission reductions and cost savings. Finally, the proposal for future tests, including investigating the correlation between valorization of ORWs and toxicity of ORW-blended composites, were proposed.