Liqing Liao

Prof. Dr. Liqing Liao


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 April 2020 in IEEE Access
Verified
Journal Article
Open access
WYWeide You
Weide You
FLFanbiao Li
Fanbiao Li
LLLiqing Liao
Liqing Liao
MHMeili Huang
Meili Huang
The indoor location technique plays a essential role during the application of quadrotor unmanned aerial vehicle (UAV). However, the control design problem for the quadrotor UAV is quite difficult in the indoor environment due to the weak GPS signal. Based on Ultra Wide Band (UWB), the related positioning issues can be solved of UAV through base station with known coordinate position and equipment with location tag, but it is difficult to meet the high-precision operation requirements. In this paper, an indoor positioning design method combined with the Inertial Measurement Unit (IMU) and UWB positioning technology is proposed, which can effectively suppress the error accumulation of the IMU and further improve the positioning accuracy. Moreover, the system architecture for a class of quadrotor UAV is designed. The multisensor fusion technology based on unscented Kalman filter (UKF) is used to avoid neglecting the high-order terms of the nonlinear observation equations of UWB and IMU, which can effectively improve the accuracy of solving the nonlinear equations. Finally, a hardware-in-the-loop simulation platform is designed to verify the effectiveness of the indoor positioning method and improve the positioning accuracy.

1 May 2022 in ISA Transactions
Verified
Journal Article
Closed access
VNVan Trung Nguyen
Van Trung Nguyen
CYChao Yang
Chao Yang
Chenglong DuChenglong Du
Chenglong Du
LLLiqing Liao
Liqing Liao

12 April 2021 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
Chenglong DuChenglong Du
Chenglong Du
FLFanbiao Li
Fanbiao Li
CYChao Yang
Chao Yang
YSYang Shi
Yang Shi
LLLiqing Liao
Liqing Liao
WGWeihua Gui
Weihua Gui
This article addresses a novel multiphase-based real-time optimal slip ratio tracking control problem of an aircraft antiskid braking system (ABS) based on the second-order sliding-mode approach. First, a comprehensive dynamic model of an aircraft ABS is established, in which the coupling mechanism of the longitudinal, the vertical, and the pitching dynamics of the aircraft are thoroughly considered. Second, for the aircraft ABS with high nonlinearity, since the measurements of aircraft velocity and acceleration cannot be transmitted to the aircraft ABS in time, the second-order sliding-mode differentiator (SMD) will be designed to estimate them simultaneously. Then, the optimal slip ratio signal, which formulates the maximum friction coefficient, will be updated based on the static friction coefficient model with real-time measured and estimated signals. Furthermore, a novel multiphase-based slip ratio regulation algorithm integrated with the second-order sliding-mode control strategy is proposed on the basis of runway characteristics to track the optimal slip ratio signal, which can not only stop the aircraft faster but prevent the mainwheel from final locking. Finally, the simulation results are presented to demonstrate that the aircraft antiskid braking algorithm proposed in this article can effectively prevent the mainwheel from locking under different runway conditions, and significantly improve the braking efficiency.

12 May 2015 in IEEE Sensors Journal
Verified
Journal Article
Closed access
CLChen Ling
Chen Ling
SWSen Wang
Sen Wang
Huosheng HuHuosheng Hu
Huosheng Hu
DGDongbing Gu
Dongbing Gu
LLLiqing Liao
Liqing Liao
This paper proposes a novel localization algorithm for an autonomous underwater vehicle equipped with a mechanical scanning sonar that has a slow frequency of data sampling. The proposed approach incrementally constructs a pose graph and conducts graph optimization to correct the robot poses. The construction of a pose graph has three stages: 1) scan generation which incorporates an extended Kalman filter-based dead reckoning algorithm that takes the robot motion into account while eliminating the sonar scan distortion caused by the motion; 2) data association which is based on Mahanalobis distance and shape matching for determining loop closures; and 3) scan matching which calculates constraints constructs pose graph. The constructed pose graph is then fed into a graph optimizer to find the optimal poses corresponding to each scan. A trajectory correction module uses these optimized poses to correct intermediate poses during the process of scan generation. Both simulation and practical experiments are conducted to verify the viability and accuracy of the proposed algorithm.

3 September 2019 in Materials
Verified
Journal Article
Open access
PDF file
HPHao Peng
Hao Peng
Ruiqing LiRuiqing Li
Ruiqing Li
XLXiaoqian Li
Xiaoqian Li
SDShan Ding
Shan Ding
MCMengjun Chang
Mengjun Chang
Pinghu ChenPinghu Chen
Pinghu Chen
The structure and composition of large-scale Al–Cu alloy ingots are inhomogeneous, and the segregation of (especially) elemental Cu negatively affects the uniformity and stability of the subsequent components. In this work, four ultrasonic generators were used to manipulate solidification/microstructures of cylindrical Al–Cu ingots (1250 mm in diameter; 3500 mm in length). The influence of ultrasonic configuration on both solidification microstructures and solute macrosegregation was investigated by changing the position parameters of generators for a fixed power. The results revealed that when the ultrasound is applied close to the center (I) from the 1/2 radius (II), the grain structure of the center undergoes significant refinement, degree of positive segregation in the center can be reduced, segregation index decreased from 0.2 to 0.15, and range of positive segregation in the center decreased from 200 to 150 mm. The segregation of elemental Cu was weakened by the combined effects of the ultrasound on the flow, heat transfer, and grain movement.

9 April 2024 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
Verified
Journal Article
Closed access
LLLiqing Liao
Liqing Liao
BYBo Yuan
Bo Yuan
GNGuangfu Ning
Guangfu Ning
WXWenjing Xiong
Wenjing Xiong
Zhangjie LiuZhangjie Liu
Zhangjie Liu
In this paper, a high voltage gain DC-DC converter is proposed for renewable power generation applications. The proposed converter includes a former step-up unit and z (z>1) resonant step-up units. The former unit includes two stages of boost circuits with a coupled inductor primary winding in each stage and the inputs and outputs of the two stage boost circuits are connected in series. Each resonant step-up unit is composed of two secondary windings of coupled inductors, two secondary leakage inductors, one resonant capacitor, and two diodes. The former step-up unit and the secondary windings contribute to high voltage gain. Meanwhile, all the switches and diodes can be considered as two devices connected in series. Therefore, the voltage stresses are lower than the output voltage especially the switches. In addition, the resonant unit helps to achieve zero-current-switching of the diodes. In order to verify the feasibility of the proposed converter, a 180 W laboratory prototype with only one resonant step-up unit has been built.