High temperature treatment is a typical detrimental situation that may significantly influence the compressive strength of cement-based materials. It was reported that the incorporation of common waste materials as supplementary cementitious materials (SCMs) can improve high temperature resistance. In this work, fly ash (FA), granulated blast-furnace slag (GGBFS), and silica fume (SF) were used as SCMs to replace cement to produce green cement-based materials. The mechanical strengths of the samples being subjected to various elevated temperatures were measured and analyzed with different SCMs contents. Results showed that when the high temperature was above 500 °C, it caused significant loss of strength, and the use of SCMs can improve the high temperature resistance of the cement-based materials with higher residual strength, especially for the GGBFS and SF blended samples. Moreover, the random forest regression algorithm was used to predict the compressive strength for the cement-based material incorporating various waste materials, and exhibited high accuracy. This work presents a comprehensive study on the regularity of changes of mechanical strength and provides a specific algorithm for the precise prediction of this occurrence, which is helpful to understand and predict the influence of high temperature treatment on green cement-based materials with various waste materials.
The development of electric resistance is a key factor affecting the performance of conductive concrete, especially the electrical–thermal performance. In this work, the effects of different influencing factors (including the water-to-binder ratio, coarse aggregate content and carbon fiber (CF) content) on the electric resistance of conductive concrete were systematically investigated. At the same time, ohmic heating (OH) curing was applied to fabricate CF-reinforced conductive concrete (CFRCC) under a negative temperature environment at −20 °C. The effects of different factors on the electrothermal properties (curing temperature and conductive stability) of the samples were studied. The mechanical strengths of the CFRCC cured by different curing conditions were also tested, and the feasibility of OH curing for preparing CFRCC in a negative-temperature environment was verified at various electric powers. This work aims to give new insights into the effects of multiple factors on the performance of CFRCC for improved concrete construction in winter.
Winter concrete construction in cold regions faces significant challenges due to extreme subzero temperatures, and the harsh environment presents new requirement for cement-based materials to resist this hostile external condition. To address this gap, this study proposes gradient Joule heating (GJH) curing for steel-fiber-reinforced high-performance concrete (SFR-HPC) in subzero environments (−20 °C to −60 °C). Compared to room-temperature (RT) curing, GJH enabled specimens at −20 °C to −50 °C to achieve equivalent mechanical properties within a short curing duration; the compressive strength of the specimens cured at such low environmental temperature still reached up to that of the specimen cured by RT curing. Moreover, the compressive strength of the specimens cured at −60 °C retained >60 MPa despite reduced performance. Specifically, the specimens cured at −20 °C, −30 °C, −40 °C, and −50 °C for 2 days exhibited compressive strengths of 75.8 MPa, 79.2 MPa, 77.6 MPa, and 75.4 MPa, respectively. FTIR/XRD confirmed that the specimens cured by GJH showed hydration product integrity akin to RT-cured specimens. Moreover, it should be noted that early pore structure deteriorated with decreasing temperatures, but prolonged curing mitigated these differences. These results validate GJH as a viable method for in situ HPC production in extreme cold, addressing critical limitations of conventional winter construction techniques.
To address the challenges of concrete construction in polar regions, this study investigates the feasibility of fabricating cement-based materials under severely low temperatures using electric-induced heating curing methods. Cement mortars incorporating fly ash (FA-CM), ground granulated blast furnace slag (GGBS-CM), and metakaolin (MK-CM) were cured at environmental temperatures of −20 °C, −40 °C, and −60 °C. The optimal carbon fiber (CF) contents were determined using the initial electric resistivity to ensure a consistent electric-induced heating curing process. The thermal profiles during curing were monitored, and mechanical strength development was systematically evaluated. Hydration characteristics were elucidated through thermogravimetric analysis (TG), X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR) to identify phase compositions and reaction products. Results demonstrate that electric-induced heating effectively mitigates the adverse effect caused by the ultra-low temperature constraints, with distinct differences in the strength performance and hydration kinetics among supplementary cementitious materials. MK-CM exhibited superior early strength development with strength increasing rates above 10% compared to the Ref. specimen, which was attributed to the accelerated pozzolanic reactions. Microstructural analyses further verified the macroscopic strength test results that showed that electric-induced heating curing can effectively promote the performance development even under severely cold environments with a higher hydration degree and refined micro-pore structure. This work proposes a viable strategy for polar construction applications.