In rockfall hazard management, the investigation and detection of potential rockfall source areas on rock cliffs by remote-sensing-based susceptibility analysis are of primary importance. However, when the rockfall analysis results are used as feedback to the fieldwork, the irregular slope surface morphology makes it difficult to objectively locate the risk zones of hazard maps on the real slopes, and the problem of straightforward on-site visualization of rockfall susceptibility remains a research gap. This paper presents some of the pioneering studies on the augmented reality (AR) mapping of geospatial information from cyberspace within 2D screens to the physical world for on-site visualization, which directly recognizes the rock mass and superimposes corresponding rock discontinuities and rockfall susceptibility onto the real slopes. A novel method of edge-based tracking of the rock mass target for mobile AR is proposed, where the model edges extracted from unmanned aerial vehicle (UAV) structure-from-motion (SfM) 3D reconstructions are aligned with the corresponding actual rock mass to estimate the camera pose accurately. Specifically, the visually prominent edges of dominant structural planes were first explored and discovered to be a robust visual feature of rock mass for AR tracking. The novel approaches of visual-geometric synthetic image (VGSI) and prominent structural plane (Pro-SP) were developed to extract structural planes with identified prominent edges as 3D template models which could provide a pose estimation reference. An experiment verified that the proposed Pro-SP template model could effectively improve the edge tracking performance and quality, and this approach was relatively robust to the changes of sunlight conditions. A case study was carried out on a typical roadcut cliff in the Mentougou District of Beijing, China. The results validate the scalability of the proposed mobile AR strategy, which is applicable and suitable for cliff-scale fieldwork. The results also demonstrate the feasibility, efficiency, and significance of the geoinformation AR mapping methodology for on-site zoning and locating of potential rockfalls, and providing relevant guidance for subsequent detailed site investigation.
Grouting has always been the main engineering measure of ground improvement and foundation remediation of hydraulic structures. Due to complex geological conditions and the interactions between the grout and the fractured rock mass, which poses a serious challenge to the grouting diffusion mechanism analysis, fracture grouting has been a research hotspot for a long time. In order to throw light on the grout diffusion process in the fractured rock mass and the influence of grout on the fracture network, and to achieve more realistic grouting numerical simulation, in this paper a grouting process simulation approach considering fluid–structure interaction is developed based on the 3D fractured network model. Firstly, the relationship between fracture apertures and trace lengths is used to obtain a more realistic value of fracture aperture; then a more reliable model is established; subsequently, based on the 3D fracture network model, different numerical models are established to calculate fluid dynamics (grout) and structure deformation (fractured rock mass), and the results are exchanged at the fluid–structure interface to realize the grouting process simulation using two-way fluid-structure interaction method. Finally, the approach is applied to analyze the grouting performance of a hydropower station X, and the results show that the grouting simulation considering fluid–structure interaction are more realistic and can simultaneously reveal the diffusion of grout and the deformation of fracture, which indicates that it is necessary to consider the effect of fluid–structure interaction in grouting simulation. The results can provide more valuable information for grouting construction.
Multi-scale 3D geological modeling technology is a vital issue to illustrate the complex geological conditions of infrastructure projects at the regional scale, engineering scale, and outcrop scale. It is also the computational basis for numerical geotechnics and seepage stabilization studies. However, empirical interactive modeling methods based on expert knowledge are mostly applied in existing numerical researches and geological structures at different scales are modeled independently, which reduces the credibility of simulation. Therefore, this research states a 3D fusion modeling method of multi-scale geological structures: (1) The multi-constraint NURBS modeling method for multi-valued strata at regional scale and the discrete fracture network modeling method for discontinuities at outcrop scale are presented. (2) The subdivision-NURBS modeling method for multiple genera geological bodies at engineering scale is raised so that the genus characteristics of geological bodies can be expressed in an objective parameterized way rather than in an empirical interactive-modeling way. (3) The Enhanced Boolean Logic Sequences of Oriented Geological Interfaces (E-BLSOGI), where the multiple genera geological bodies at engineering scale and the discontinuities at outcrop scale are additionally introduced based on the BLSOGI method offered in authors’ previous study [1], is provided to achieve 3D fusion modeling of multi-scale geological structures. The practice indicates that the 3D fusion modeling of multi-scale geological structures is realized, evidencing that results without integrating multi-scale geological structures underestimate the compressive stress (16.37, 10.52, and 33.09%), tensile stress (16.57, 21.57, and 10.76%), and displacement (7.17, 47.62, and 33.62%) of the dam foundation in x -, y -, and z-, directions, respectively.