Puerarin (daidzein-8-C-glucoside), one of the bioactive isoflavones, has attracted attention in various industries due to its excellent pharmacological effects such as antioxidant effect, estrogen-like activity, reduction of blood sugar, and neuroprotective effect. Puerarin is most abundantly found in the roots of Pueraria lobata (RPL) among various biomass sources. To improve the utilization feasibility of puerarin, a high-yield extraction process should be designed for RPL. This study aimed to optimize the extraction process to more efficiently recover puerarin from RPL while using generally recognized as safe solvents as extraction solvents, considering the potential industrial applications of puerarin. The extraction variables were optimized by the one-factor-at-a-time method, response surface methodology, and time profiling study. As a result, puerarin yield was achieved at 60.56 mg/g biomass under optimal conditions (ethanol concentration of 46.06%, extraction temperature of 65.02 °C, ratio of extraction solvent to biomass of 11.50 mL/g, and extraction time of 22 min). High puerarin yield achieved in this study contributed to improving the industrial applicability of puerarin.

Carbon aerogel is a promising material in various applications, such as water treatment, insulators, catalysts, and sensors, due to its porosity, low density, conductivity, and good chemical stability. In this study, an inexpensive carbon aerogel was prepared through lyophilization and post-pyrolysis using waste paper. However, carbon aerogel, in the form of short belts, is randomly entangled without a crosslinking agent and has weak mechanical properties, thus limiting its applications, which would otherwise be various. In this paper, a novel strategy is proposed to fabricate a PDMS-coated carbon aerogel (Aerogel@PDMS). Benefiting from microwave heating, precise PDMS coating onto the carbon frame was able to be carried out in a short amount of time. PDMS coating firmly tied the carbon microstructure, maintaining a unique aerogel property without blocking its porous structure. FE-SEM, RAMAN, XPS, and FT-IR were all used to confirm the surface change in PDMS coating. Compressible stability and water contact angle measurement showed that Aerogel@PDMS is a perspective organic solvent absorbent due to its good resilience and its hydrophobicity, and, as a result, its organic solvent absorption capacity and repeated absorption were evaluated, ultimately suggesting a promising material in oil clean-up and pollution remediation in water. Based on our experimental results, we identified elastic carbon aerogels provided by a novel coating technology. In the future, then, the developed carbon/PDMS composite can be examined as a promising option for various applications, such as environmental sensors, virus sensors, and wearable sensors.

In this study, a transient viscosity adjustment method using a coaxial nozzle was explored to fabricate nanofibers from non-spinnable m-poly(hydroxyamide) (m-PHA). Unlike conventional electrospinning methods that often require additives to induce fiber formation, this approach relies on a sheath-core configuration, introducing tetrahydrofuran (THF) to the sheath to temporarily adjust solution viscosity. The diffusion of THF into the core m-PHA solution resulted in momentary solidification at the interface, promoting nanofiber formation without compromising polymer solubility. SEM and rheological analyses confirmed that optimized sheath-to-core flow ratios yielded nanofibers with significantly reduced particle formation. Notably, increasing the THF flow rate facilitated a faster solidification rate, enhancing jet elongation and resulting in uniform nanofibers with diameters of approximately 180–190 nm. Although complete nanofibers without beads were not achieved in this study, this coaxial electrospinning approach presents a possible pathway for fabricating nanofibers from polymers with limited spinnability, potentially expanding the application scope of electro-spun materials in high-performance fields.

Sea buckthorn berries (SBB) are well known for being rich in natural bioactive compounds with high pharmacological activity. In this study, the optimization of extraction parameters was performed to recover phenolic compounds with high antioxidant activity from SBB. This study involved a systematic optimization approach, including screening for a variety of parameters, including temperature, time, ethanol concentration, agitation, and solid loading. On the basis of Plackett–Burman design (PBD) model, the two most significant parameters (agitation and solid loading) were selected, and the correlation model between those parameters and multiple responses was derived via response surface methodology (RSM). As a result, the optimal extraction condition for maximizing phenolic content and antioxidant activity was determined to be agitation at 109.54 rpm and a solid loading of 172.67 g/L. Under optimal conditions, SBB extract showed a total phenolic content of 0.21 mg/mL and ABTS and DPPH activities of 27.27% and 58.16%, respectively. The SBB extract prepared under optimal conditions was found to contain caffeic acid, vanillic acid, rutin, and vitamin B1 (thiamine). This work is the first challenge to design an optimization model for the efficient recovery of antioxidants from SBB and is significant in that the model can be applied simply and economically to conventional extraction processes.